For use in all outdoor power equipment where a "00" grease is recommended. 1 quart bottle.

"00" & EP-O semi fluid grease for chain saw tips, sprockets, trimmer heads, gear cases. 4oz bottle.

High torque "00" grease, easy to use container. For use in all outdoor power equipment where "00"grease is recommended, 9oz tube.

Original Kawasaki air filter replaces OEM# 11013-7024.  Also replaces Cub Cadet 798-00573 & Gravely 21535900.  Fits FH601V-FH721V; for 19 thru 25 HP vertical shaft engines.  Externally vented carburetor.

7-3/8" length, 3-1/2" width, 3" height.  Can use our KA9584F prefilter(not included)

This item is not in our catalog

Original Kawasaki filter replaces Kawasaki 11013-7027  Fits Models: KAWASAKI FH601V, FH641V & FH721V. Interally vented carburetor 
Length: 7 3/8" , Width: 3 1/2", Height: 3" 

can use our KA9584F prewrap(not included)

This item is not in our catalog

Briggs & Stratton starter gear replaces OEM#s 280104, 280104S, 693059 & 695708.  This item is not in our current catalog

Contains 190 pieces, 11 different sizes.

Replaces O.E.M. #527011, Complete air lift kit used on AR30A blades

Replaces O.E.M. #03121300, 03121359, 03121351, Length 14-5/8", Center Hole 3/4", Width 2", Thickness .204. (3) blades for 42" cut. Deck #831038GT.

Replaces O.E.M. #03027800, 03027859, 03027851, Length 16-5/8", Center Hole 3/4", Width 2-1/2", Thickness .180. (3) blades for 48" cut. Also, Center blade for Ariens 60" cut, GT-Decks.

Replaces O.E.M. #31237, 3123759, 03123751, Length 16-5/8", Center Hole 3/4", Width 2-1/2", Thickness .204. (3) blades for 48" cut. Deck #381031GT

Replaces O.E.M. #34853, 3485351, Length 16-5/8", Center Hole 3/4", Width 2-1/2", Thickness .204. (3)AR16B blades & (3) AR16A 48" cut (blades cross) To make a mulching kit

Replaces O.E.M. #11370, 01128500, 01137059, 01137051, Length 20-1/2", Center Hole 13/32", Width 2-3/4", Thickness .160. Zone start mower. Zone start mower.  Used on 21" walkbehind mowers

Replaces O.E.M. #011384, 1138451 Length 20-1/2", Center Hole 11/16", Outside Hole 3/8", Width 2-3/4", Thickness .134. Used on 21" BBC walkbehind mowers.  **Limited supply**

Replaces O.E.M. #27287, #2728759, 00351400, 02532500, 02728751, Length 30", Center Hole 3/4", Outside Hole 25/64", Width 2-3/4", Thickness .187. For 30" rear engine rider. Uses our No. AL-911 Air Lifts

Replaces NGK TR-5, Replaces Champion RS14YC, Replaces Autolite 106. 106 Autolite Plug.

Replaces NGK B6L, Replaces Champion H10, Replaces Autolite 216. 216 Autolite Plug.

Replaces NGK BM6A, Replaces Champion CJ6 & CJ8, Replaces Autolite 255. 255 Autolite Plug.

Replaces NGK BPM6F, Replaces Champion DJ7Y, Replaces Autolite 2554. 2554 Autolite Plug.

Replaces NGK BM6A, Replaces Champion CJ6 & CJ8, Replaces Autolite 255. 255 Autolite Service Pack, 24 Plugs/Service Pack.

Replaces NGK BM4A, Replaces Champion CJ14, Replaces Autolite 258. 258 Autolite Plug.

Replaces NGK BR4HS & BP4HS, Replaces Champion L92YC, Replaces Autolite 275. 275 Autolite Plug.

Replaces NGK B6S, Replaces Champion J8 & J8C, Replaces Autolite 295. 295 Autolite Plug.

Replaces NGK BM7F, Replaces Champion DJ6, Replaces Autolite 2954. 2954 Autolite Bantam Tapered Seat C/S Plug. **LIMITED SUPPLY**

Replaces NGK BM6F, Replaces Champion DJ8J, Replaces Autolite 2956. 2956 Autolite Bantam Tapered Seat Plug.

Replaces NGK BPM7A, Replaces Champion CJ7Y, Replaces Autolite 2974. 2974 Autolite Plug.

Replaces NGK BPM6A, Replaces Champion CJ8Y, Replaces Autolite 2976. 2976 Autolite Bantam Gasket Seat Plug.

Replaces NGK B4, Replaces Champion J11C, Replaces Autolite 306. 306 Autolite Plug.

Replaces NGK B2, Replaces Champion RJ19LM, Replaces Autolite 308. 308 Autolite Plug.

Replaces NGK B8S, Replaces Champion J4C, Replaces Autolite 353. 353 Autolite Plug. **LIMITED SUPPLY**

Replaces NGK A6 & A7, Replaces Champion D14, D16J, D21, Replaces Autolite 386. 386 Autolite Plug.

Replaces NGK BCPR6ES, Replaces Champion RC12YC, Replaces Autolite 3924. 3924 Autolite Plug.

Replaces NGK B9ES, Replaces Champion N2C & N2G, Replaces Autolite 4053. 4053 Autolite Plug. **LIMITED SUPPLY**

Replaces NGK BR8ES, Replaces Champion RN3C, Replaces Autolite 4063. 4063 Autolite Plug.

Replaces NGK B8HS, Replaces Champion L82C, Replaces Autolite 4092. 4092 Autolite Plug.

Replaces NGK B7HS, Replaces Champion L82C, UL4J, UL81C, UL81J, Replaces Autolite 4093. 4093 Autolite Special.

Replaces NGK B4H & B6HS, Replaces Champion RL86C & L86C, L14 & L90, Replaces Autolite 425. 425 Autolite Plug.

Replaces NGK BP6ES, Replaces Champion N9YC, Replaces Autolite 4253. 4253 Autolite Special Electrode plug.

Replaces NGK BP6ES, Replaces Champion RN9YC, Replaces Autolite 4263. 4263 Autolite Plug.

Replaces NGK BP5ES, Replaces Champion N11YC, Replaces Autolite 4265. 4265 Autolite Plug.

Replaces NGK B4LM, Replaces Champion J8 & J17LM, Replaces Autolite 456. 456 Autolite Plug.

Replaces NGK B4LM, Replaces Champion J8 & J17LM, Replaces Autolite 456. 456 Autolite Service Pack, 24 Plugs/Service Pack.

Replaces NGK B4LM, Replaces Champion J19LM, Replaces Autolite 458. 458 Autolite Plug.

Replaces NGK UR4, Replaces Champion RBL16Y, Replaces Autolite 26. 26 Autolite Plug.

Replaces NGK BPR5ES, Replaces Champion RN11YC, Replaces Autolite 64. 64 Autolite Plug.

Replaces NGK XR-5, Replaces Champion RJ14YC, Replaces Autolite 86. 86 Autolite Plug.

Backpack Blower Rack.

• Blowers mount & secure conveniently on hook with spring latch
• Includes rubber strap to secure equipment
• (Not for Stihl BR-Series)
• Powder coated finish. Not lockable. Holds most backpack blowers.

Backpack Blower Rack.

• Designed specifically for Stihl BR340 & BR420 blowers
• Blower rests on bottom support and is secured on top hang pin
• Secures with padlock (not included)

 

The Battery Tender is a 1.25 amp battery charger that automatically switches from full charge to floating charge mode, and then monitors the battery. Designed to fully charge a battery and maintain it at a proper storage voltage without the damaging effects caused by trickle chargers. For lead acid and gel cell batteries only. Has 6ft cord. Made in the U.S.A. 5yr warranty.

Replaces Ransomes/Bobcat 31007A. Left hand (53 degree).

Replaces Ransomes/Bobcat 31006A. Right hand (53 Degree).

Replaces Ransomes/Bobcat 31005A. Variable speed (90 degrees).

Replaces Ransomes/Bobcat 35010A and Snapper/Kees 76439. Coil Diameter-1/2", Length Overall-4-7/16", Length of Coil - 2-3/4", Thickness - 3/32".

Replaces Bobcat 32344. Used on all 36" and 48" cut gear drive units. Holds belt on engine pulley.

Replaces Bobcat 32345-01. Used on all variable speed new models. Holds belt on engine pulley.

Replaces Bobcat 32345-02. Used on older model single belt variable speed mowers. Uses (2) on engine pulley and (4) on wheel drive pulley.

Blade balancer made of the finest steel with sealed bearings for precision balancing and strong magnets to hold a blade while balancing.

Replaces Bunton PL0815. Overall 9" length.

Replaces Scag 04001-41 & Ferris 1525019-76, Encore 100353 & Wright 11990007. Fits 32", 40", 48", 52", 61" and 72" mowers. 5/8" x 9-7/8" overall length.

Replaces O.E.M.#90105-960-710, code 1663665. Mower models HR214, HRA214, HR215, HRA215, HR216, HRA216, HRC215, HRC216, HRM215, HRB215 and HRS21. Hex Flange Bolt.

Replaces Ransomes/Bobcat 64163-12, Bunton PL0617, Exmark 303164, 1-323539, Scag 43278 & 43038, and Snapper/Kees 76436 & Ferris 1541477. ID- 5/8", OD- 1", Thickness- 1/4".

Replaces Scag 43278 (fits new style spindles). ID-5/8", OD-1-1/2", Thickness-1/4".

1/2" blade spacer used on Bobcat, Bunton, Exmark, Scag and Snapper. ID-5/8", OD-1", Thickness-1/2".

Replaces Ariens O.E.M.# 3192800, Bobcat 48045B, Cub Cadet IH-395789-R2, 723-3014, 923-3014, Gravely 039306, John Deere AM39653, AM35176, Toro 79-5270, 108335.

Replaces Bobcat #138008. Fits 36", 48", & 54", & 61" mid size mowers - formed to a 5"ID.

Replaces Bobcat #38183. Fits 48" mid-size. Transmissions to wheel. ID- 5/8", OD- 3-7/16", Height- 1-13/16, Keyway- 3/16".

Replaces Bobcat #38232. Fits 36" midsize. Transmission to wheel. ID- 5/8", OD- 3-7/16", Height 1-1/4", Keyway- 3/16".

Replaces Bobcat 31012A engine pulley without set screws & 31008B spindle pulley. ID-1", OD-5-3/4", Height - 1-3/16", Keyway- 1/4".

Replaces Bobcat #38010-2A. ID- 3/8", OD- 3-1/32", Height- 7/8".

Replaces Bobcat #38184-2. Idler for double "v" drive wheel pully to gear and positive drive. Fits 36", 48", 54", and 61". ID- 3/8", OD-4", Height- 1-9/16".

Replaces Bobcat #31011B. ID- 1", OD-5-3/4", Height 1-5/16". Keyway- 1/4".

Replaces Bobcat #38022B. ID-5/8". OD-5", Height- 1-5/16" Keyway- 3/16"

Replaces Ransomes/Bobcat #38140 & #38089N. ID- 1" to 1/2", OD-5", Height- 3-1/2", Keyway 1/4".

Replaces Bobcat #36271. For rear drive wheels with double V-belts. ID 2-5/16", OD 8-7/8", Height 1/2".

Replaces Bobcat #2720759. Replaces Bunton #2720759. Fits ZT223 with 52" deck. Right hand and left hand sides.

Replaces Bobcat #2186207. Replaces Bunton #2186207. Fits ZT223 with 61" deck-Center.

Replaces Bobcat #2702758 & 2720758. Replaces Bunton #2720758 & 2702758. Fits ZT223 with 52" deck-Center.

Replaces Bobcat #2186205. Replaces Bunton #2186205. Fits ZT223 with 61" deck. Right hand and left hand sides.

Output shaft support bracket bearing replaces Bobcat #35062B used with MP8184 flange.  Also replaces Exmark 303067

6" caster yoke. Replaces Bobcat 36306 & 36013A, Bunton PL0556, JD PT8670, Kees 362101, 976401, Lesco 050173 & Snapper 76400. (used with our support arm #CYS2218).

Replaces Bobcat OEM #38389, Newer Models. Deck Cross Drive Belt on 36" XM Series-OEM spec belt.

Replaces Bobcat newer models OEM #38470. Veri-Deck Units - 36" Mulching-OEM spec belt.

Replaces O.E.M. #38017N.  Wheel Drive-Single V - OEM spec belt.

Replaces Bobcat belt OEM# 38439 gear belt for 48" cut XM Series. OEM spec belt.

Replaces Bobcat belt OEM#s 38458 & 38463. Hydro, 36" cut XM series. OEM spec belt.

Replaces OEM# 128003. Cutter deck belt for ZTR Rider 61".  OEM spec belt

Replaces O.E.M. #38212. 36"/48" Dual Wheel Drive - OEM spec belt.

Replaces O.E.M. #38185 & 38249.  Dual Wheel Drive Belt - OEM spec belt.

Replaces O.E.M. #38440. 48" Hydro-Deck Belt - OEM spec belt.

Replaces O.E.M. #2188128. 61" Rider-Eng/Hydro Pump-OEM spec belt.

Replaces O.E.M. #38442. 48" Gear Drive-Eng./Deck-OEM spec. belt

Replaces O.E.M. #38523. 1994-1996 Wheel Drive Belt-OEM spec belt.

Replaces O.E.M. #128099. Gear Drive Mowers - Trani Belt-OEM spec belt.

Caster yoke support arm. Replaces Ransomes/Bobcat 36129 and Bunton PL0457 (used with our caster yoke #CYS2243). Comes complete with bushings and grease fitting. Uses our bushing #DBU5721.

Support arm. Replaces Bobcat 36482. Comes complete with bushings and grease fitting. Uses our DBU5707 bushings. Use with our CYS6581 yoke.

4" yoke replaces Bobcat 36411 and 36526.

Replaces Bobcat 6416307, 64163-07. Used on our CYS6581 caster yoke. ID-1", Thickness-1/4", OD-1-3/4".

Replaces Bobcat 6416322, 64163-22 & Ferris 1541476. Used on our CYS6581 caster yokes.  ID-1", Thickness-1/2", OD-1-11/16".

Support arm mounting bracket replaces Bobcat 36091B. Used with our CYS8181 and CYS8349 support arms.

Caster support arm with bushings replaces Bobcat 46233. Fits 48", 61" and 74" front mount decks. Uses our DBU5707 bushing. ***Limited Supply, OUR SUPPLIER HAS DISCONTINED, only 1 available**

Caster support arm with bushings and replaces Bobcat 46102C. Fits 48", 61" and 74" front mount decks. Uses our DBU5707 bushings. ****LIMITED SUPPLY*****our supplier has discontinued

3-1/2" yoke with 8" shaft. Replaces Bobcat 36377. ***limited supply***

Replaces Bobcat #2721246. Fits Bobcat ZTR rider mowers. Size 8 x 22. Extended length 10.08".

Replaces Ransomes/Bobcat 480532A. Used on Bobcat support arm 46102C. Used on our CYS8181, CYS6580, and CYS8349 support arms. Also fits Snapper 23556, Pro7 and Ferris 20822. ID-1", OD-1-1/4", Height-3/4", Flange OD-1-5/8".

Replaces Ransomes/Bobcat 33050. Used on our support arm CYS2218. ID-3/4", OD-1", Height-1-3/16".

Replaces Bobcat 43037A. Used in 280/250x4 front caster wheels. ID-3/4", OD-1", Length-3-1/2".

Replaces Bobcat #65263A. Used to hold transmission shaft bearings on 36", 54" and 61" decks. Uses MP8077 bearing.

Replaces Bobcat 36493.  **Limited Supply--discontinued item** 

Bobcat (21" rear bagger) (special order). Heavy duty military spec. latch, Curved front directs grass to back of catcher for high density packing, Non vented front construction of catcher keeps grass from clogging mower outlet, Weighs 19.5# and holds 3.3 cubic feet. Tubular steel frame continuous weld superior to spot-weld catchers, 22 gauge solid and perforated sheet steel.

Bobcat catcher assembly Pre 1994, Heavy duty military spec. latch, Curved front directs grass to back of catcher for high density packing, Non vented front construction of catcher keeps grass from clogging mower outlet, Weighs 19.5# and holds 3.3 cubic feet. Tubular steel frame continuous weld superior to spot-weld catchers, 22 gauge solid and perforated sheet steel.

Bobcat Catcher assembly Jumbo (Pre 1994), Heavy duty military spec. latch, Curved front directs grass to back of catcher for high density packing, Non vented front construction of catcher keeps grass from clogging mower outlet. Jumbo weighs 23# and holds 4.3 cubic feet. Tubular steel frame continuous weld superior to spot-weld catchers, 22 gauge solid and perforated sheet steel.

Bobcat (1994 & newer) Heavy duty military spec. latch, Curved front directs grass to back of catcher for high density packing, Non vented front construction of catcher keeps grass from clogging mower outlet, Weighs 19.5# and holds 3.3 cubic feet. Tubular steel frame continuous weld superior to spot-weld catchers, 22 gauge solid and perforated sheet steel.

Bobcat (1994 & newer) Jumbo Size. Heavy duty military spec. latch, Curved front directs grass to back of catcher for high density packing, Non vented front construction of catcher keeps grass from clogging mower outlet. Jumbo weighs 23# and holds 4.3 cubic feet. Tubular steel frame continuous weld superior to spot-weld catchers, 22 gauge solid and perforated sheet steel.

Replaces O.E.M. #38016N.  Transmission OEM spec belt

Replaces O.E.M. #38030N. 48" Main Blade Belt - OEM spec belt.

Replaces O.E.M. #38031N. 48" Short Deck Belt- OEM spec belt.

Replaces O.E.M. #38111. 36" Main Deck Belt - OEM spec belt.

Replaces O.E.M. #38234. 36" Engine/Blade Belt - OEM.

Replaces O.E.M. #38039N.  32" Main Deck Belt.

Replaces O.E.M. #38111.  36" Main Deck Belt.

Replaces O.E.M. #38016N.  Transmission Belt

Replaces O.E.M. #38234.  36" Engine/Blade Belt.

Replaces O.E.M. #38030N.  48" Main Blade Belt.

Replaces O.E.M. #38031N.  48" Short Deck Belt.

Replaces O.E.M. #78030. 21" mower -  M214SP (older models), Jackshaft.

Replaces O.E.M. #78031. 21" mower -  M214SP (older models), Jackshaft to Wheel.

Replaces O.E.M. #38211. 36"/48" Engine/Trani belt-OEM spec belt.

Replaces Bobcat #128079. Female 1/4" - 28 rod end assembly.

No Flange Flat Idler Pulley. Replaces Bobcat 38184-1. ID-3/8", OD-2-3/4", 1" Offset Hub.

Replaces Bobcat 36567. Fits 36" &48" XM series Mowers.

Replaces Bobcat #43090A. Fits 36" and 48" Hydro drive mowers. 5/16"-18. RH and LH threads.

Replaces Bobcat 64123-86 for 8" caster wheel.

Replaces Bobcat 64151-12.

Open cage roller bearing with bushings. Used on 6"x2.00" heavy duty front caster wheels. Bearings replace Bobcat 38069N and bushings replace Bobcat 38042N. Used on our WBOBO12. Overall ID-5/8", Overall OD-1-13/32", Overall Length-2-7/32".

Complete kit can be used for 9x350x4 front caster wheels. Includes (2) high speed bearings (5/8"IDx1-3/8"ODx7/16" thick), (1) spanner bushing (1/2"IDx5/8"ODx4-1/16" length), and (2) washers.

Replaces Bobcat 78113. Used on wheels from Bobcat push mowers. ID-1/2", OD-3/4", Height-1".

Wheel bearing kit replaces Bobcat 38058N (roller cage bearing) & 38025N (retainers). Fits Bobcat 38096C wheel assembly. Bearing (7/8"ID, 1-3/8"OD, 6-7/8" over all length).

Replaces Bobcat 6416371, 6416314, Bunton PL0417. ID-25/32", Thickness-1/4", OD-1-1/4". Used on our CYS2243 yoke.

Wheel size 280/250-4, polyurethane sawtooth tire on 3-piece red wheel with 1" open cage roller bearing.  Flat Free Tire.

Wheel size 9x350-4, polyurethane smooth tire on 3-piece red wheel with 5/8" open cage roller bearing. Flat Free Tire.

Replaces O.E.M. #32061A, 32061. Length 16-1/4", Center Hole 5/8", Outside Hole 11/32", Width 2-1/2", Thickness .240, Heavy Duty, (2) blades for 32" cut, (3) blades for 48" cut

Replaces O.E.M. #112111-01, Length 16-1/4", Center Hole 5/8", Width 2-1/2", Thickness .204, (2) blades for 32" cut, (3) blades for 48" cut (formed blade)

Replaces O.E.M. # 32061 & 32061A, Length 16-1/4", Center Hole 5/8", Outside Hole 1/4", Width 2-1/2", Thickness .150, (2) blades for 32" cut, (3) blades for 48" cut

Replaces O.E.M. #32022A, Length 18", Center Hole 5/8", Width 2-1/2", Thickness .240 Heavy Duty (2) blades for 36" cut, (3) blades for 54" cut

Replaces O.E.M. #112111-02, Length 18", Center Hole 5/8", Width 2-1/2", Thickness .204 (2) blades for 36" cut, (3) blades for 54" cut (formed blade)

Replaces O.E.M. #32022A, Length 18", Center Hole 5/8", Outside Hole 1/4", Width 2-1/2", Thickness .150 (2) blades for 36" cut, (3) blades for 54" cut

Replaces O.E.M. #112243-02, Length 18", Center Hole 5/8", Width 2-1/2", Thickness .204 (2) blades for 36" cut, (3) blades for 54" cut (Low Lift)

Replaces O.E.M. #72039B, Length 21", Center Hole 3/8", Outside Hole 3/8", Width 2-1/2", Thickness .150, 21" Push Mower

Replaces O.E.M. #42180B, Length 21", Center Hole 5/8", Width 2-1/2", Thickness .240. Heavy Duty (3) blades for 61" cut

Replaces O.E.M. #112111-03, Length 21", Center Hole 5/8", Width 2-1/2", Thickness .240. Heavy Duty (3) blades for 61" cut (formed blade)

Replaces O.E.M. #112243-03, Length 21", Center Hole 5/8", Width 2-1/2", Thickness .240. Heavy Duty (3) blades for 60" cut

Replaces O.E.M. #42139B, 112111-04, Length 25", Center Hole 5/8", Width 2-1/2", Thickness .240. Heavy Duty (3) blades for 74" cut

Replaces Bobcat/Ransomes O.E.M.#126167 and 128028. Also replaces Warner #5215-18. Pulley 6", Height 3-7/16", Bore 1". Uses 5/8" belt. Confirm O.E.M.# prior to ordering. 25% restocking fee on all returned Electric PTO Clutches.

Replaces O.E.M. #172-7926 Length 15-5/16", Center Hole 3/8", Outside Hole 3/8", Width 2", Thickness .204. Fits models 18300, 30042R & 30042S center mount mower (3) blades for 42" cut

Replaces O.E.M. #189-3850 Length 21-13/16", Center Hole 1/2", Outside Hole 3/8", Width 2", Thickness .187. For 22" mulcher.  **LIMITED SUPPLY**

Replaces Briggs & Stratton # 270579 and John Deere M47949 foam air filter. Length 4-1/2" to 5-3/8", width 3" to 3-1/2", thickness 1-1/2". This item is not in our catalog.

Filter replaces Briggs & Stratton #697014, 697634, 697153 & 698083. Fits AVS models 284H07, 285H07, 286H07 and 31E700, 31G700, 31H700 series. 8-3/4" Lx3-1/8"Wx1-1/2"HT.

Filter replaces Briggs & Stratton # 697152, 613022 and 6984-13. Fits models 21A900 and 21B900 series. 7"Lx3-1/8"Wx1-1/2"HT.

Replaces O.E.M. 497725. Fits 5HP Quantum engines models 12U800 thru 12U899. OD- 3-7/8", ID- 2-5/8", Height 2-3/16".

Replaces Briggs & Stratton #691564 and 808106. Fits models 350000-380000 with steel flywheels. Special order. 30% restocking fee if returned. Match OEM# before ordering.

Replaces Briggs & Stratton #496881. Fits our BS10709 starter. Special order. 30% restocking fee if returned. Match OEM# before ordering

Briggs air filter replaces OEM# 792105.  Also replaces John Deere MIU11515.  Fits 40G-40H & 44H-44K series engines. 

Length- 5-1/8", Width- 2-3/4", Height- 4-1/2"

Briggs pre-filter replaces OEM# 792303.  Used with our BS12479 air filter.

Briggs & Stratton air fitler replaces OEM# 793569.  Also replaces John Deere GY21055 & MIU11511.

Length- 2-7/8", Width- 1-1/2", Height- 5-7/8"

Starter rewind spring replaces OEM#490179, 294303. Fits model Numbers 60000, 80000, 81000, 82000, 92000, 93000, 100000, 111000, 130000, 131000, 146000, 147000,170000, 171000, 190000, 191700, 195000, 220000. (Top mount side pull).

Starter rewind spring replaces OEM#390066. Fits model numbers 94500, 94900, 110900. (Vertical pull starter).

Starter rewind spring replaces OEM#492194, Fits 9 HP to 18 HP Vanguard engines.

Starter rewind spring replaces OEM# 491889, 99700, 121700, 121800, 123800, 124800, 126800, 122700 and 124700, Magnum engines.

Foam prewrap for part BS8815.

Replaces Briggs O.E.M.# 492932, 492932S, 492056, 696854, John Deere AM125424 and Tecumseh 36563. Fits Briggs 14 & 18 HP Vanguard engines. 25/30 micron. Also fits 15-17 HP Intek engines. Thread size 3/4"-16", O.D. 2-15/16", Ht 2-1/4",micron 25/30.

Replaces Briggs & Stratton #497595. Fits single cylinder aluminum engines. 16 tooth gear. Special order. 30% restocking fee if returned. Match OEM# before ordering

Replaces Briggs & Stratton #497596. Fits most twin cylinder engines. 16 tooth gear. Special order. 30% restocking fee if returned. Match OEM# before ordering.

Replaces Briggs & Stratton #497401. Heavy duty, fits single cylinder aluminum engines 16 tooth gear. Special order. 30% restocking fee if returned. Match OEM# before ordering.

Replaces Briggs & Stratton #498148. Heavy duty, fits most twin cylinder engines. 16 tooth gear. Special order. 30% restocking fee if returned. Match OEM# before ordering

Replaces Briggs & Stratton #396306. 16 tooth gear. Special order. 30% restocking fee if returned. Match OEM # before ordering.

Briggs & Stratton fuel cap replaces OEM#s 298425 & 493982.

Replaces Briggs & Stratton # 494559 and #490075. Fits 5 HP model 130202 engine.

Replaces Briggs & Stratton #397974. Fits 100700 series, 3-1/2 thru 5 HP Vertical, Max and Quantum engines.

Fuel cap replaces Briggs & Stratton 493988. Fits 7 - 12-1/2 HP vertical engines.

Replaces Briggs & Stratton #497929. Fits Briggs & Stratton 3.5 and 3.75 HP Classic and Sprint engines and 4 HP Quattro engines. 1-1/2? ID.

Replaces Briggs & Stratton #496106 and 490547. Fits 4-1/2 and 5 HP Quantum models.

Replaces Briggs & Stratton #392989. Fits 9-16 HP single engine cylinder engines. Series 233400-252700, 254400, 2870700, 281700, 326400, 402400 and 422400. For 1" pipe, 1" pipe thread, ID 1-1/4".

Replaces Briggs & Stratton #498984 and 493963 & Bunton 252762. Fits 12 HP series 252762 muffler. Fits Sears and midsize Exmark, Bunton and Toro. For 1-1/4" pipe OD.

Replaces Briggs & Stratton #491413  691874. Low-tone muffler for 10 to 12-1/2 HP horizontal and vertical engines.

Replaces Briggs & Stratton 392989, 299477, 393232 (8-16 HP). Tecumseh 32043B and Kohler 275679. Also fits Wisconsin & Gravely. Fits many John Deere, Wheel Horse, and Power King. For 1" pipe. 1" pipe thread, ID-1-1/4".

Foam prewraps for BS0184. Replaces Briggs OEM# 697015.

Foam Pre-filter replaces OEM# 697292 for our BS0263.

Starter pulley replaces B&S 280918. Fits models 290400, 290700, 294700, 303400, 303700, 350400 & 350700. Fits 8HP & up Vanguard engines, OD - 6-3/8", ID 1/2".

Starter pulley B&S 498144. Fits models 121600-699, 125800-899, 122600-699, 134400-499, 134200-299, 133200-299, 135400-499, 136200-299, 137200-299. Fits 5&6 HP vertical intrek engines. OD 5-1/2". Comes with spring.

Replaces O.E.M. 491021. Fits 12.5 & 14 HP vertical single cylinder OHV Vanguard engine 260700 & 261700 series. OD- 6-3/4", ID- 2-7/8", Height 3-1/8".

Replaces O.E.M. 492947. Foam prewrap for BS021.

Replaces O.E.M. 272405, 272922. 8 HP Horz. & Vert Engines/Foam Filter/ fits 194700 & 195700 series. OD- 8-1/8", ID- 2-3/4", Height- 1".

Replaces O.E.M. 394019. Twin cylinder 12, 14, 16, 18 HP. IC vertical models 402700, 421700, 400700, 401700, 404700. Uses foam wrap BS06F. OD- 9-5/8", ID- 4", Height- 2-1/2".

Replaces O.E.M. 270093. Round foam filter for 7 thru 14 HP early style Fits models 190400, 300400, 320400. OD- 4-13/16", ID- 1-1/4", Height- 3-1/8". **LIMITED SUPPLY**

Replaces O.E.M. 805113. 12.5, 14 & 16 HP horz. & vert. V-Twin OHV Vanguard engines. Fits models 290400, 290700, 294400, 294700, 303400, 303700- Waffle panel filter. OD- 7-3/8", ID- 6-5/16", Height- 3/4".

Replaces O.E.M. #392286. Fits models 252400, 253400, 255400 (10, 11, &12HP) vertical engines.

Replaces O.E.M. #272235. Fits models 92500, 92900, 93900, 95900, 96500, & 96900 Sprint and classic engines (3, 3.5 & 3.75 HP) vertical shaft. Length or O.D. 4-3/4-5-1/2", Width or I.D. 3-1/4-4", Thickness or HT. 1-1/2".

Replaces O.E.M. 399959, 491588. 3 & 5 HP Horz. Waffle Panel filter. Also fits 3.5 & 5 HP Quantum engines (top starter). Also fits JD #PT15853. OD- 5-1/4", ID- 4-1/2", Height 1".

Replaces O.E.M. 491384. 9 HP OHV Vanguard engine fits model 161400- Waffle panel filter. OD- 7", ID- 3-1/2", Height- 1-1/2".

Replaces O.E.M. 491435, 493537. Foam Prewrap for BS38.

Replaces O.E.M. 393406. 7 & 8 HP vert. 190700, 191700, 192700, 193700, 170700 series, oval shaped. OD- 5-3/16", ID- 3-1/8", Height- 2-1/2".

Replaces O.E.M. 491519, 399806. 10 thru 12 HP. I/C Vert. model 281700, 280700, 253700, 256700. Uses foam wrap BS41F. OD- 8-5/8", ID- 2-5/8", Height 2-3/4".

Replaces O.E.M. 399877. 3.5 HP Quantum/ 100700 series (side starter) waffle panel filter. OD- 4-5/8", ID- 4-5/8", Height - 7/8".

Replaces O.E.M. #270251. Fits 82500 Series thru 92900 & 92500 series for 3-3/1 HP engines. Length or O.D. 5-5-3/4", Width or I.D. 2-7/8-3-5/8", Thickness or HT. 2-7/8-3-5/8".

Replaces O.E.M. #270528. Fits 8 HP horizontal engines 146700-147703, 170700, 171700, 190700, 191700 - fits 7&8 HP vertical engines. Length or O.D. 7-3/4-8-1/4", Width or I.D. 3-5/8-4-1/4", Thickness or HT. 1-1/2".

Replaces O.E.M. #393957. 7 thru 16 HP horz. engines. Fits models 170400, 171400, 190400, 19440, 19540, 220400, 221400, 222400, 233400, 243400, 252400, 253700, 254400, 290400, 294400, 302400, 303400, 326400. Uses foam wrap BS74F. Length or O.D. 4-1/4", Width or I.D. 2", Thickness or HT. 3-3/4".

Replaces O.E.M. #270782, 271794. Foam prewrap for part BS74.

Replaces O.E.M. #270447. Fits 130900 Series 5 HP horizontal models. Length or O.D. 5-3/8-6", Width or I.D. 3-3-5/8", Thickness or HT. 1-1/2".

Replaces O.E.M. #392642, 394018. 16 & 18 HP horizontal 402400, 421400, 422400 and V-Twin OHV Vanguard. Uses foam wrap BS77F. OD- 7", ID- 5-5/8", Height 2-1/8".

Replaces O.E.M. 393725. 11 HP I/C vertical series. Fits models 220700, 252700, 253700, 256700- oval shaped. OD- 5-3/16, ID- 3-1/4", Height- 2-1/2".

Replaces O.E.M. #494511. Fits 5HP 133400 series industrial plus engines. OD- 7", ID, 3-1/2", Height- 1-1/4".  Uses our BS384F prefilter.

Replaces O.E.M. 399968 Fits 7, 8 and 11 HP engine. OD- 8-3/4", ID- 3-1/4", Height- 2-1/2".

Replaces O.E.M. 496077. Fits 8 HP industrial Plus engines. OD- 7", ID- 3-1/2", Height- 1-1/2".

Replaces O.E.M. #396424. Fits 2 thru 5 HP horz. and vert. engines. Uses foam wrap BS88F. Length or O.D. 2-3/4", Width or I.D. 1-1/4", Thickness or HT. 2-3/4".

Replaces O.E.M. 710266. Fits 9HP Vanguard model 185400- Waffle panel filter. OD- 8-3/8", ID- 4", Height- 1-1/8".

Replaces O.E.M. 397795. 3.5 & 4 HP I/C. Waffle panel filter- Max Series. OD- 6-1/4", ID- 4-1/2", Height- 7/8".

Replaces O.E.M. 493909, 496894. Fits 12 thru 15 HP vertical engines- models 282700, 283700, 286700. OD- 7-1/8", ID- 2-1/2", Height- 2-7/8".

Replaces O.E.M. 272403. Foam prewrap for BS909.

Replaces O.E.M. 710265. Filter replaces Briggs and Stratton. 710265. Fits 4HP horizontal Vanguard engine. OD- 6-5/16", ID- 3-1/2", Height- 1".

Replaces Briggs O.E.M. #s 498596, 697029 & 690610.  Fits 5.5 & 6.5 HP Intek engines. OD- 3-9/16", ID- 2-1/4", Height- 3".  Can use our BS9591F prewrap for this filter

Replaces O.E.M. 499486. Filter replaces Briggs and Stratton 499486. Fits InteK 14-24 HP engines. OD- 7", ID- 4", Height- 1-1/2".  Uses our BS9304 prefilter

Replaces O.E.M. 491950. Fits HP Vert. OHV Vanguard Engine, 104700 series- types 3122, 4024, 4025, 4044, 4045. OD- 5-1/2", ID- 2-1/2", Height- 2-3/4".

Replaces O.E.M. #270848 4 HP vertical engines 110900 & 111900. Length or O.D. 4-3/4-5-1/2", Width or I.D. 3-1/4-4", Thickness or HT. 1-1/2".

Replaces O.E.M. 493910 & 691667. Fits 8.5 thru 11.5 HP vert engines models 196700, 257700, 259700.

Replaces O.E.M. 805267. Foam Prewrap for BS113.

Replaces O.E.M. 271962 Foam prewrap for part BS41.

Replaces O.E.M. 272533/273185 Foam Prewrap

Replaces O.E.M. 399039. Foam prewrap for BS89.

Replaces O.E.M. 273638S. Foam prewrap for BS9273.

Replaces O.E.M. 272218. Foam Prewrap for BS950.

Replaces O.E.M. #692446. Fits 123600 series. Length or O.D. 4", Width or I.D. 2-1/2" Thickness or HT. 3"

Replaces O.E.M. #273356. Foam prefilter for BS9591 and BS9168

Replaces O.E.M. 492889. Foam Pre-filter for BS384, BS7877, BS7880.

Replaces OEM# 271939. Foam Pre-filter for our BS7879.

Replaces O.E.M. 271271, 272490. Foam prewrap for part BS06.

Replaces O.E.M. #271271/272490. Foam prewrap for BS77.

Replaces O.E.M. #271466. Foam prewrap for part BS88.

Replaces O.E.M. 272477. Foam Prewrap for BS0910.

BrushGuard is recommended for use with outdoor power tools, such as line trimmers, power blowers and lawn mowers. The nylon shield is a convenience shield, and it does not meet ANSI requirements for impact and penetration. BrushGuard, Orange earmuff with 22mB NRR, and nylon mesh face shield (7"x14").

Built for commercial use. Single or dual line indexing. Recommended for use on trimmers under 30cc. Replaces the following OEM Trimmer Heads. ECHO SRM 200BE; 200CE; 200DA; 200AE; 400AE, 400BE; 1500; 1501; 2200; 2201; 2300; 2301; 2400; 2500; 2501; 2502; 3000; 3001; 3010; 3800; 4600. HOFFCO JP260; JP270; JP390; JP390XL, JP420D. JOHN DEERE 90G; 240G; 250G; 300G; 350G; 450G; 24S; 25S; 30S; 38B. KAAZ J40FD; JQ50; RQ30; T240; V15; V25; V35; V40. MARUYAMA BC184C; BC241; BC402; BC184C; BC200C; BC260C. MC CULLOCH 99A; EB3; MAC100A; PS1; PS2; PS3; PS4; PS5; SEB4; PROSCRAPER TITAN 2300; 2400. SACHS DOLMAR BC210; BC212; LT250. SNAPPER 221SST; 215SST; 240SST; 245SSTBC; 410SST; 311. SOLO S100; S400. TORO TC600; TC650; TC700; TC800; TC3000; TC3100; TC3500; TC4000; TC5000.

Replaces Bunton PL8036A. Fits 48" and 52" mid size Hydro and BHC front engine riders.

Replaces Bunton PL8540A. Idler pully fits Bunton 61" and 71" cut Hydro Rider commercial machine models.  ID-3/8", OD- 4-7/8", Height- 7/8".

Replaces Bunton PL4274. Fits Mid size Bunton, Bobcat & Exmark mowers with double wide drive belt. ID- 3/8", OD- 3-1/2", Height 1-1/2".

Brake band only. Replaces PL1155AL. Fits left side on 32-61" decks equipped with stub axles.

** LIMITED SUPPLY, DISCONTINUED ITEM **

Blade to Blade Belt, 32", replaces OEM# PL0543

Replaces O.E.M. #PL6062.  61" Engine to Deck Belt.

Replaces O.E.M. #PL4055 Length 16", Center Hole 5/8", Width 2-1/2", Thickness .204. (3) blades for 48" cut (Standard Lift)

Replaces O.E.M. #PL4855 Length 16-1/2", Center Hole 5/8", Width 2-1/2", Thickness .204. Low lift blade (3) blades for 48" cut. Gear & Hydro drive mid-size V-deck models

Replaces O.E.M. #PL4205 Length 16-1/2", Center Hole 5/8", Width 2-1/2", Thickness .204. High lift blade. (3) blades for 48" cut. Gear & Hydro drive. Mid-size V-deck models.

Replaces O.E.M. #P2005 Length 18", Center Hole 5/8", Width 2-1/2", Thickness .204. (3) blades for 52" cut (Standard Lift)

Replaces O.E.M. #PL4206. Length 18", Center Hole 5/8", Width 2-1/2", Thickness .204. (2) blades for 36" cut. (3) blades for 52" cut. (High Lift). Also replaces Snapper #29246.

Replaces O.E.M. #PC005 Length 21", Center Hole 5/8", Width 2-1/2", Thickness .204. (3) blades for 61" cut

Replaces O.E.M. #PL4275.  Double Wheel Drive Belt  - OEM spec belt.

Replaces O.E.M. #PL7332. 60"-Deck Belt for ZTR Mower.

Replaces O.E.M. #PL1361. 61" Engine to Blade Belt.

Replaces O.E.M. #PL7436.  50" & 60"- Engine to Deck Belt.

Replaces O.E.M. #PL1443. 48" Blade to Blade Belt-Cogged.

Replaces O.E.M. #PL0848.  Variable Speed Belt  - OEM spec belt

Replaces O.E.M. #PL8519.  61" Blade to Blade Belt.

Replaces O.E.M. #PL0648.  32" Engine to Transmission Belt.

Replaces O.E.M. #PL4734.  48" Blade to Blade Belt.

Replaces O.E.M. #PL4740. Double Wheel Drive Belt - OEM spec belt.

Replaces O.E.M. #PL7014.  61" Engine to Blade Belt - OEM spec belt.

Replaces O.E.M. #PL4732.  48" Engine to Blade Belt - OEM spec belt.

Replaces O.E.M. #PL4811.  48" Engine to Blade Belt.

Replaces O.E.M. #PL0619. Wheel Drive Belt-Cogged-OEM spec belt.

Replaces O.E.M. #PL4733.  36" Engine to Blade Belt - OEM spec belt.

5" caster yoke replaces Bunton PL7010W. Fits 36", 48", 52" 61" and 72" cut midsize commercial mowers.

Replaces Bunton PLO928. Used on Bunton support arm PAL0937A, Exmark 303041, and Snapper/Kees 76515. ID-7/8", OD-1-1/8", Height-1-1/4".

Replaces Bunton PJH1060. Fits all Midsize Hydro and belt driven mowers. Also fits John Deere M83541. ID-1", OD-1-1/4", Height-1", Flange OD-1-3/4".

Replaces O.E.M. #Z32008.

Replaces Bunton PLO636, ID- 5/8", OD- 3-1/2", Height 1-5/16", Keyway- 3/16".

Bunton (1995-2000) Hydro & gear drive-except 36") Heavy duty military spec. latch, Curved front directs grass to back of catcher for high density packing, Non vented front construction of catcher keeps grass from clogging mower outlet, Weighs 19.5# and holds 3.3 cubic feet. Tubular steel frame continuous weld superior to spot-weld catchers, 22 gauge solid and perforated sheet steel.

Bunton (1995-2000)Hydro & gear drive- except 36") Jumbo size. Heavy duty military spec. latch, Curved front directs grass to back of catcher for high density packing, Non vented front construction of catcher keeps grass from clogging mower outlet. Jumbo weighs 23# and holds 4.3 cubic feet. Tubular steel frame continuous weld superior to spot-weld catchers, 22 gauge solid and perforated sheet steel.

Bunton (1995-2000 Hydro & gear drive- 36") Heavy duty military spec. latch, Curved front directs grass to back of catcher for high density packing, Non vented front construction of catcher keeps grass from clogging mower outlet, Weighs 19.5# and holds 3.3 cubic feet. Tubular steel frame continuous weld superior to spot-weld catchers, 22 gauge solid and perforated sheet steel.

Bunton (1995-2000 Hydro & gear drive- 36") Jumbo Catcher. Heavy duty military spec. latch, Curved front directs grass to back of catcher for high density packing, Non vented front construction of catcher keeps grass from clogging mower outlet. Jumbo weighs 23# and holds 4.3 cubic feet. Tubular steel frame continuous weld superior to spot-weld catchers, 22 gauge solid and perforated sheet steel.

Replaces O.E.M. #PL5039. Variable Speed Belt 

Replaces O.E.M. #PL0511.  32" & 36" Engine/Blade Belt.

Replaces O.E.M. #PL0021.  40" Deck Belt.

Replaces O.E.M. #PL4511. 36" Engine to Blade Belt.

Replaces O.E.M. #PL0643. 36" & 52" Blade to Blade Belt. Also replaces John Deere #PT8676.

Replaces O.E.M. #PL0661.  36" Engine to Blade - Long.

Replaces O.E.M. #PL4811. 48" Engine to Blade Belt.

Replaces O.E.M. #PL4813.  48" Engine to Blade Belt.

Replaces O.E.M. #PL0861.  52" Engine to Blade Belt.

Replaces O.E.M. #PLO643.  36 & 52" Blade to Blade Belt-OEM spec belt.

Replaces O.E.M. #PL4739.  52" - Engine to Blade Belt - OEM spec belt.

Replaces O.E.M. #PL0511. 32" & 36" Engine to Blade Belt-OEM spec belt.

T-Knob replaces Bunton PL4020. Fits our TC8766 Throttle Control.

Replaces Bunton PJ-5019-50. Fits Bunton midsize commercial hydro mower 36", 48", 52", & 60" cut. Used with our TC8800 T-knob. Conduit 50", Inner wire 52-1/4", Wire travel 2-1/4"

Replaces Bunton #PLO346. Fits 36", 48", 52" and 60" cut on older Bunton midsize mowers. 17" long

Replaces O.E.M. #PAL0942A, Wheel size 410/350-5 Caster wheel used on 32", 36", 48", 52" and 61" mulch and turf decks/ 410/350-5, 2-ply sawtooth tire and tube, mounted 3/4" semi-sealed machine ball bearing, 3" centered hub, 1-piece wheel, painted yellow.

Replaces O.E.M. #PAL1075A, Wheel size 13x650-6, Complete rear wheel drive assembly / 13x650-6 4-ply turfsaver tire mounted 1-piece rim with 7/8" open cage roller bearing, single pully, brake drum and zerk fitting, painted yellow. For single wheel drive belt mowers.

Bunton, John Deere (not stamped deck, not GS series), Heavy duty military spec. latch, Curved front directs grass to back of catcher for high density packing, Non vented front construction of catcher keeps grass from clogging mower outlet. Jumbo weighs 23# and holds 4.3 cubic feet. Tubular steel frame continuous weld superior to spot-weld catchers, 22 gauge solid and perforated sheet steel.

Bunton, John Deere (not stamped deck, not GS series), Heavy duty military spec. latch, Curved front directs grass to back of catcher for high density packing, Non vented front construction of catcher keeps grass from clogging mower outlet, Weighs 19.5# and holds 3.3 cubic feet. Tubular steel frame continuous weld superior to spot-weld catchers, 22 gauge solid and perforated sheet steel.

Contains 10 (total of 100) popular size reducer bushings used in most idler pulley applications.

1/2" Press - Inside Diameter - 1", Outside Diameter - 1-3/8".

1/2" Press - Inside Diameter - 1/2", Outside Diameter - 1-3/8".

1/2" Press - Inside Diameter - 3/4", Outside Diameter - 1-3/8".

1/2" Press - Inside Diameter - 5/8", Outside Diameter - 1-3/8".

1/2" Press - Inside Diameter - 7/8", Outside Diameter - 1-3/8".

3/4" diameter cutting capacity. High carbon steel, fully heat treated blade, hook and handle. Ergonomic non-slip grip. Easy to operate unobtrusive lock. Large bearing surface for easier cuts. Lightweight, easy to use.

Quickly dissolves gum, varnish, lead, and carbon deposits. Extra strength designed for professional shop use. 16 oz. can.

Replaces O.E.M. #C24441 Length 13-3/4", Center Hole 1-1/4", Outside Hole 7/16", Width 2-1/2", Thickness .187. (3) blades for 38" cut, Left hand cut.  **LIMITED SUPPLY**

Replaces O.E.M. #C24442, C12262 Length 15-9/16", Center Hole 1-1/4", Outside Hole 7/16", Width 2-1/2", Thickness .187. (3) blades for 44" cut, Left hand cut

Replaces O.E.M. #C24443, C14885, Length 15-7/8", Center Hole 1-1/4", Outside Hole 7/16", Width 2-1/2", Thickness .187. Takes (1) #CA16A & (2) #CA17 for 48" cut. Left hand cut

Replaces O.E.M. #C14886 Length 17", Center Hole 1-1/4", Outside Hole 7/16", Width 2-1/2", Thickness .187. Takes (2) #CA17 & (1) #CA16A for 48" cut. Left hand cut

Replaces O.E.M. #01010168, Length 17-29/32", Center Hole 3/4", Width 2.5", Thickness .204. High lift blade (3) blades for 50" cut. Fits tank commercial.

RBG Ceramic blue grinder stone, Diameter 12", Thickness 1", Center Hole 7/8".

RBG Ceramic blue grinder stone , Diameter 10", Thickness 1", Center Hole 3/4".

8" Diameter Ceramic blue grinder stone. 1" thickness, 5/8" center hole.

Replaces NGK FR4, Replaces Champion 2071, Replaces Autolite 3924. Champion 2071 Premium Gold Plug.

Replaces NGK BM4A, Replaces Champion CJ14, Replaces Autolite 258. CJ14 Champion Plug.

Replaces NGK BM4A, Replaces Champion CJ14, Replaces Autolite 258. CJ14 Champion Service Pack 24 Plugs/Service Pack.

Replaces NGK BM7A, Replaces Champion CJ6, Replaces Autolite 254. CJ6 Champion Plug.

Replaces NGK BPM7A, Replaces Champion CJ7Y, Replaces Autolite 2974. CJ7Y Champion Plug.

Replaces NGK BM6A, Replaces Champion CJ8, Replaces Autolite 255. CJ8 Champion Plug.

Replaces NGK BM6A, Replaces Champion CJ8, Replaces Autolite 255. CJ8 Champion Service Pack, 24 Plugs/Service Pack.

Replaces NGK BPM6A, Replaces Champion CJ8Y, Replaces Autolite 2976. CJ8Y Champion Plug.

Replaces NGK A7, Replaces Champion D14, Replaces Autolite 386. D14 Champion Plug.

Replaces NGK A6, Replaces Champion D16, Replaces Autolite 386. D16 Champion Plug.

Replaces NGK BM7F, Replaces Champion DJ6J, Replaces Autolite 2954. DJ6J Champion Plug.

Replaces NGK BM6F, Replaces Champion DJ8J, Replaces Autolite 2956. DJ8J Champion Plug.

Replaces NGK B4L, Replaces Champion H10C, Replaces Autolite 215, 216, 217. H10C Champion Plug.

Replaces NGK B4LM, Replaces Champion J17LM, Replaces Autolite 456. J17LM Champion Plug.

Replaces NGK B4LM, Replaces Champion J17LM, Replaces Autolite 456. J17LM Champion Service Pack 24 Plugs/Service Pack.

Replaces Champion J19LM, Replaces Autolite 458. J19LM Champion Plug.

Replaces Champion J19LM, Replaces Autolite 458. J19LM Champion Service Pack 24 Plugs/Service Pack.

Replaces NGK B6S, Replaces Champion J8C, Replaces Autolite 295. J8C Champion Plug.

Replaces NGK B6S, Replaces Champion J8C, Replaces Autolite 295. J8C Champion Service Pack 24 Plugs/Service Pack.

Replaces NGK B8HS, Replaces Champion L78C, Replaces Autolite 4092. L78C Champion Plug.

Replaces NGK B7HS, Replaces Champion L82C, Replaces Autolite 4092. L82C Champion Plug.

Replaces NGK B6HS, Replaces Champion L86C, Replaces Autolite 425. L86C Champion Plug.

Replaces NGK BP6ES, Replaces Champion N9YC, Replaces Autolite 4253. N9YC Champion Plug.

Replaces NGK BCPR6ES, Replaces Champion RC12YC, Replaces Autolite 3924. RC12YC Champion Plug.

Replaces NGK BCPR6ES, Replaces Champion RC12YC, Replaces Autolite 3924. RC12YC Champion Service Plug 24 Plugs/Service Pack.

Replaces NGK 4626, BPMR7A, Replaces Champion RCJ6Y, Replaces Autolite 2974 & 2984. RCJ6Y Champion Plug.

Replaces NGK BPMR6A, Replaces Champion RCJ8Y, Replaces Autolite 2985. RCJ8Y Champion Plug.

Champion RDZ19H plug. Fits Ryobi 4 cycle trimmer.

Replaces NGK B2, Replaces Champion RJ19LM, Replaces Autolite 308. RJ19LM Champion Plug.

Champion RJ19LM/24 plugs.

Replaces Autolite 275. Champion RL95YC Plug.

Replaces NGK BPR5ES, Replaces Champion RN11YC4, Replaces Autolite 64. RN11YC Champion Plug.

Replaces NGK BR6ES, Replaces Champion RN4C, Replaces Autolite 403. RN4C Champion Plug.

Replaces NGK BPR6ES, Replaces Champion RN9YC, Replaces Autolite 4263. RN9YC Champion Plug.

Replaces NGK TR5, Replaces Champion RS14YC, Replaces Autolite 106. RS14YC Champion Plug.

Replaces NGK TR4, Replaces Autolite 106. Champion RS17YX Plug.

Champion RC14RC Register plug.

Champion RJ12C plug.

Champion RH10C plug. Replaces Autolite 216.

22x1100-8, Chevron Tread - 3 ply belted tubeless for ZTR machines

Choke control replaces Scag 48780. Fits Scag push-pull design. Conduit 51", inner wire 57", wire travel 2".

Replaces Bobcat 64188-21 and 64140-2. Clevis pin for Traction control handle. Comes complete with Cotton pin.

Lightweight polished aluminum allow. Exclusive comfort tool grip. 3 rigid straight tines penetrate hard ground. Designed for a lifetime of use.

Lightweight polished aluminum alloy. Exclusive comfort tool grip. 3 rigid straight tines. Designed for a lifetime of use.

Lightweight polished aluminum allow. Exclusive Comfort Tool grip. Narrow profile ideal for flower pots. Marked and graduated for depth. Designed for a lifetime of use.

Lightweight polished aluminum alloy. Exclusive Comfort Tool grip. Wide 3" blade. Designed for a lifetime of use.

Replaces O.E.M. #s Dixie Chopper 30227-50, 30227-50V, Dixon 9258, 9265, Gravely 087792, 046998 & Toro 113579. Length 17", Center Hole 5/8", Width 2-1/2", Thickness .204. Commercial Mulcher Blade. (3) blades for 50" cut

Has everything you need to rebuild your worn trani. Rebuilding kit for our GB097 Gear box assembly.

Replaces Bunton PL6140A, PL4606A, PL6139, PAL0806A, PT8633, JD-AM106236, AM122797, and Lesco 050164. Fits 36", 40", 48", 52" and 61" cut (6-1/2" length, 25mm diam. spindle shaft).

Spindle Assembly replaces Encore 362044 & 422022.

Spindle Assembly replaces Encore 363379, Shaft length 6-1/2".

Spindle Assembly replaces Encore 583106, Shaft length 6-1/2".

For 48" decks (long shaft) Replaces Ransomes/Bobcat 36082N, Exmark 402006, Lesco 050150, Jacobsen 552312, Snapper/Kees 59964 & 76645, 482005, 101446. With grease fitting.

Spindle Assembly replaces Great Dane D18030, shaft length 6".

Replaces Scag 46020 & 46400, Ferris 1530301, Lesco 050194, and Wright 71460007. Uses our replacement bearing SB7178. For 1994 and older Scag. 7-3/16" shaft length, 1" shaft OD.

For 32" & 36" decks (short shaft). Replaces Ransomes/Bobcat 36006N, Lesco 050135, Exmark 302030, Jacobsen 552188, Snapper/Kees 362024, 59759 and 76379, 101455, Lesco 050135. With Grease Fitting.

188" std. conduit, 50" rolls. Used with our inner wire #TC245.

203" Hvy. Duty conduit, 50" roll. Used with our inner wire #TC246.

Replaces Bobcat 33004A, Bunton PLO355, Exmark 303099, and Jacobsen 552203.

3/4" diameter cutting capacity. Resharpenable blade and brass anvil. Concealed return spring-close tolerance pivot bolt. Thumb-lock pistol grip design. Vinyl coated handles.

555 piece Cotter Pin assortment. From 1/16"x1" up to 5/32"x2-1/2" sizes.

Coupler with cover replaces Exmark 324340, 1-323501 & Scag 481581. Fits 5 speed mowers. Comes with grease fitting and cover. 9-spline center. Used with our MP9580 drive shaft.

Replaces O.E.M. #734-3058B, Wheel size 5"x2.75". Plastic heavy duty deck wheel for 38", 40" and 50" cut decks. 2-1/2" offset with 1/2" bore. Also replaces Ariens 03471700, AYP 133957, Excel 031997, MTD 734-3058B, Murray 92265 and Simplicity 1700184.

3 in 1 blade replace Cub Cadet OEM#s 742-3033 & 759-3830.  Fits deck series 1500 & 1517.  2 blades used for 42" cut.  Length- 21-1/4", Width- 2-3/4", Centerhole- 3/4", .204 Thickness.

Cub Cadet blade replaces OEM# 742-04068 & 942-04068. 3 blades used for 50" cut. 17.90" length, 2-3/8" width, 3/4" round center hole, .160 thick. Fits Series 1000 Hydrostatic lawn tractors, model LT1024.

Cub Cadet blade replaces OEM# 742-04053A & 942-04053A.  3 blades used for 50" cut. 17.90" length, 2-3/8" width, modified star center hole, .160 thick. Fits RZT series tractors, model RZT50.

Replaces O.E.M. # 01005336, Length 17", Center Hole 3/4", Width 3", Thickness .204. (3) blades for 48" cut high lift blade

Replaces O.E.M. # 01005337, Length 19", Center Hole 3/4", Width 3", Thickness .204. (3) blades for 54" cut high lift blade.

Replaces O.E.M. # 01005338, Length 21", Center Hole 3/4", Width 3", Thickness .204. (3) blades for 60" cut high lift blade.

Replaces O.E.M. #742-3001, #759-3811, 490470, 473-427-R1, 759-3400, 759-3836, Length 10-1/4", Center Hole 3/4", Width 2-1/2", Thickness .204. 1968 to 73 models takes (2) #CC10 & (1) #CC20 for 38" cut

**LIMITED SUPPLY** discontinued item                                 

Replaces O.E.M. #1004719, Length 20-1/2", Center Hole 3/4", Width 3", Thickness .204. (3) blades for 60" cut. Fits Cub Cadet and MTD Pro ZTR's with stamped steel decks.

Replaces O.E.M. #954-3038. 38" Deck 1000 Series - OEM spec belt.

Replaces O.E.M. #759-3939, Length 16", Center Hole 3/4", Width 2-1/2", Thickness .204. (3) blades for 44" cut. Used on mowers from 2002 and newer

Replaces O.E.M. #954-3036. 38" Spindle Drive Belt - models 190-331-OEM spec belt.

Replaces O.E.M. #954-3073. 42" Deck Belt-2000 Series-models 190-142. OEM spec belt.

Replaces O.E.M. #954-0644. 42" Deck Belt - OEM spec belt.

Replaces O.E.M. #954-0645. 42" Deck Belt - OEM spec belt.

Replaces O.E.M. #490489-R2. 38", 42" & 48" PTO Deck Drive Belt-models 70, 86, 123, 169 OEM spec belt.

Replaces O.E.M. #477-598-R3, 490-471-R1, 759-3848, 759-3844, Length 11", Center Hole 3/4", Width 2-1/2", Thickness .204. 1968 to 73 models takes (2) #CC11 & (1) #CC22 for 42" cut

replaces Cub Cadet blade OEM# 01008616. High lift blade for Z-Force Zero turn rider. 3 blades used for 44" cut.
15.94" length, 3" width, 3/4" center hole, .204 thickness.

Replaces O.E.M. #487-762-R1, 490-472-R1, 490-472, 490427-R1 & 487-762-R1. Length 14-1/2", Center Hole 3/4", Width 2-1/2", Thickness .204. Takes (2) #CC14 & (1) #CC20 for 48" cut

Replaces O.E.M. #742-3002, 759-8312, 759-3812, 59704-C1, Length 15-1/8", Center Hole 3/4", Width 2-1/2", Thickness .204. (3) blades for 44" cut current models

Replaces O.E.M. #489-393-R1, 490-475-R1, 759-3847, Length 16", Center Hole 3/4", Width 2-1/2", Thickness .204. Takes (2) #CC16 & (1) #CC17A for 48" cut

Replaces O.E.M. #742-3019, 759-3825 & 742-3025. Length 16-1/2", Center Hole 3/4", Outside Hole 5/16", Width 2-1/2", Thickness .204. (3) blades for 48" cut Garden tractor model 2000 & Pro mid-size Walkbehind

Replaces O.E.M. #742-3003, 759-3813, 59705-C1, Length 17-3/16", Center Hole 3/4", Width 2-1/2", Thickness .204. (3) blades for 50" cut

Replaces O.E.M. #489-392-R1, 759-3846, Length 17-5/8", Center Hole 3/4", Width 2-1/2", Thickness .204. Takes (1) #CC17A & (2) #CC16 for 48" cut

Replaces O.E.M. #742-3013, 759-3820, Length 18-1/2", Center Hole 3/4", Width 3", Thickness .204. (3) blades for 54" cut Garden Tractor & Pro mid-size Walkbehind

Replaces O.E.M. #742-3008, 759-3816, Length 19-5/16", Center Hole 3/4", Width 3", Thickness .204. (2) blades for 38" cut (High Lift)

Replaces O.E.M. #742-3009, 759-3817, Length 19-3/8", Center Hole 3/4", Outside Hole 5/16", Width 3", Thickness .204. (2) blades for 38" cut, front engine rider models 1015, 1020, 1030, 1715, 1720

Replaces O.E.M. #742-3000, 759-3810, 742-3399, 490-476-R1, 487-761-R1, Length 20", Center Hole 3/4", Width 2-1/2", Thickness .204. Takes (1) #CC20 & (2) #CC10 for 38" cut. Takes (1) #CC20 & (2) #CC14 for 48"cut.

Replaces O.E.M. #117-453-C1, Length 20-3/4", Center Hole 3/4", Width 2-1/2", Thickness .204. For model #3160-A

Replaces O.E.M. #547-191-R1, 759-3853, Length 21-1/4", Center Hole 3/8", Outside Hole 17/32", Width 2-1/2", Thickness .204. (3) for 60" cut

Replaces O.E.M. #742-3018, 759-3824 & 742-04101.  Length 21-3/16", Center Hole 3/4", Outside Hole 5/16", Width 3", Thickness .204. (2) blades for 42" cut. Garden tractor models 2000 & 1440

Replaces O.E.M. #477-597-R3, 490-473-R1, 759-3850, 759-3843, Length 22-3/16", Center Hole 3/4", Width 2-1/2", Thickness .204. 1968 to 73 models takes (1) #CC22 & (2) #CC11 for 42" cut.

Replaces Cub Cadet OEM# 754-3068 & 954-3068. PTO Belt - 2000 Series, 46" & 48" Deck - OEM spec belt.

Blade bolt replaces Cub Cadet 710-04226.  Fits LT 1000 series riders & Cub Cadet 618-04123B spindle assembly.  For 38", 42", 46" & 50" decks. 

Size 3/4" - 16 x 5.85"
 

Commercial Mulching Blades replaces Cub Cadet OEM#s 742-04053A & 942-04053A.  Fits RZT series tractors.  3 blades used for 50" cut.

Length- 17.9", Centerhole- modified star, Width- 2-1/2", Thickness- .187.

 

Replaces Cub Cadet #751-0226A. Fits 1980 thru 1989 models. 10-5/8" overall length. 2-1/4" dia., 2-7/8" OD. Made by an OEM supplier.

Replaces OEM #703-1890 & 903-1890. Wheel Size: 5" x 2.5". Fits models LT48, GT42, GT46, GT48, GT54, 44A, 50A. 2-3/8" offset with 1/2" bore.

Replaces Bobcat 14380, 43180, Ferris 1541657 & Scag 43022. Used in our wheel bearing assembly WB8313 & WB7780. ID-1/2", OD-5/8", Length-4".

Replaces Dixie Chopper O.E.M. #s 30227H, 30227-50H and Toro/Wheelhorse 113579 Heavy Duty blade.  Length 17", Center Hole 5/8", Width 2-1/2", Thickness .204. (3) blades for 50" cut ZTR.

Replaces Bobcat #38010-1A, 2306005 and Snapper/Kees 76500 and 76688. ID 3/8", OD- 4-5/8", Height- 11/16".

 

Replaces Exmark 403009 and Gravely 21060. ID- 3/8", OD- 4-5/8", Height- 11/16"

 

Deluxe Rubber Coated Trimmer Rack. Holds up to 3 trimmers. 3/16" black rubber coating. Includes locks. Includes locking pins. Outside mounting. Mounting hardware included.

Deluxe Rubber Coated Trimmer Rack. Holds up to 3 trimmers. 3/16" black rubber coating. Includes locks. Includes locking pins. For Inside Enclosed Trailer. Mounting hardware included.

Clean and restore sharpness of a wheel that has become loaded with the material being ground. Increases wheel life and performance. For RGB1012C & RBG3410C.

Clean and restore sharpness of a wheel that has become loaded with the material being ground. Increases wheel life and performance. For BG121.

Replaces O.E.M. #392606 For 5 amp tri-circuit harness alternators. Fits Briggs & Stratton 6 amp diodes instead of OEM 3 amp.

Replaces O.E.M. #393456 For 2-4 amp dual circuit alternators. Fits Briggs & Stratton 6 amp diodes instead of OEM 3 amp.

Replaces O.E.M.# 393814 For 2-4 amp charging systems. Fits Briggs & Stratton 6 amp diodes instead of OEM 3 amp.

Replaces O.E.M. #10202, 13x500-6, 4-ply rib tire on 1-piece silver rim, 5/8" sealed machined ball bearings, 3-3/4" centered hub with Zerk. Fits Dixie Chopper ZTR mowers 1999 & later.

Replaces O.E.M. #97166, Wheel size 13x650-6, 4-ply rib tire, 1 piece, silver rim, 5/8" sealed machined ball bearings, 3-3/4" centered hub with zerk.

Dixie Chopper brake band replaces OEM# 65244 parking brake.

Caster yoke replaces Dixie Chopper 10201.  **LIMITED SUPPLY** discontinued item

Roller bearing replaces Dixie Chopper #97171, Fits caster yoke bearing #LM44610 and #LM44649. ID-1-1/8", OD-2", Height-5/8".

Replaces O.E.M. #65080. Deck Belt for 50" & 60" Cut (B80) -OEM spec belt.

Replaces O.E.M. #9907B84. Engine to Deck Drive Belt -OEM spec belt.

Replaces O.E.M. #97346C158. 72" Mule Drive Belt-w/Yanmar Diesel Engines-OEM spec belt.

Replaces O.E.M. #30227-42, Length 14-1/2", Center Hole 5/8", Width 2-1/2", Thickness .203. (3) blades for 42" cut.

Replaces O.E.M. #30227-50, Length 17", Center Hole 5/8", Width 2", Thickness .204. (3) blades for 50" cut.

Replaces O.E.M. #20256.  Engine to Transmission Belt  (B38)- OEM spec belt.

Replaces O.E.M. #30227-60-V, Length 20-1/2", Center Hole 5/8", Width 2-1/2", Thickness .240. (3) blades for 60" cut (High Lift for wet grass)

Replaces O.E.M. #30202.  Engine to Deck Belt.

Replaces O.E.M. #30203.  50" Deck Belt.

Replaces Dixie Chopper O.E.M. #30204.  Engine to Deck Belt - OEM spec belt.

Replaces O.E.M. #302220.  Engine to Gear Box Belt.

Replaces Dixie Chopper O.E.M. #63203.  Deck Belt - OEM spec belt.

Replaces Dixie Chopper O.E.M. #63204.  Engine to Transmission Belt - OEM spec. belt

Replaces O.E.M. #30227-72H, Length 24", Center Hole 5/8", Width 2-1/2", Thickness .240. (3) blades for 72" cut.

Replaces O.E.M. #30227-60H, Length 20-1/2", Center Hole 5/8", Width 3", Thickness .240. (3) blades for 60" cut (High Lift)

Replaces O.E.M. #30227N, 30227H (high lift). Length 17", Center Hole 5/8", Width 3", Thickness .240. (3) blades for 50" cut. Fits ZTR models (High Lift).

Replaces O.E.M. #30227-50V, Length 17", Center Hole 5/8", Width 2-1/2", Thickness .240. (3) blades for 50" cut. High Lift for wet grass.

Replaces O.E.M. #68081.  Engine Belt - (B81) -OEM spec belt.

Replaces O.E.M. #68082.  Engine to Deck Belt - (B82) -OEM spec belt.

Replaces O.E.M. #68162.  Deck Belt Fits 72" Cut.- OEM spec belt

Replaces O.E.M. #30227-72N, Length 24", Center Hole 5/8", Width 3", Thickness .240. (3) blades for 72" cut. Heavy duty.

Replaces Dixie Chopper O.E.M. #97345.  Engine to Transmission Belt - OEM spec belt

Replaces Dixie Chopper O.E.M. #9907A96.  Deck Belt - OEM spec belt

Replaces Dixie Chopper O.E.M. #9907B112.  Deck Belt - OEM spec belt.

Replaces Dixie Chopper O.E.M. #9907B130.  Deck Belt - OEM spec belt.

Replaces Dixie Chopper O.E.M. #9907B41.  Engine to Transmission Belt - OEM spec belt.

Replaces Dixie Chopper O.E.M. #9907B57.  Pump to Engine Belt - OEM spec belt

Replaces Dixie Chopper O.E.M. #9907B85.  Engine to Deck Belt - OEM spec belt.

Replaces Dixie Chopper O.E.M. #9907B92. Engine to Deck Belt - OEM spec belt

Replaces Dixie Chopper O.E.M. #9907B94. Deck Belt - OEM

Replaces Dixie Chopper 10222. Coil Diam. 7/8" Total Length 6-1/4" Length of Coil 4-1/8" Thickness 1/8".

V-Belt idler pulley replaces Dixie Chopper 30224. Heavy Duty. ID-1/2", OD 4-3/4", Height-1-1/4".

V-Belt idler pulley replaces Dixie Chopper 30234. Also replaces Toro 65-5948. Heavy duty riveted pulley. ID-5/8". OD 4-3/8", Height-1".

Replaces O.E.M.#30227-42. Length 14-1/2", Center Hole 5/8", Width 2-1/2", Thickness .204, Commercial Mulcher Blade. (3) blades for 42" cut.

Replaces O.E.M. #302360.  60" Deck Belt - OEM spec belt.

Replaces OEM# 10161-L. Spindle Assembly replaces Dixie Chopper 50" and 60" rider. Long shaft. Center assembly. Over all height 9-1/2".

Spindle assembly replaces Dixie Chopper #10161. Fits Dixie Chopper 50" and 60" rider. Short Shaft. Outside assembly.

Replaces Dixie Chopper #10202 & 97166 wheel assemblies. Bearing kit fits our 506DC-DIXIE and 656DC-DIXIE Wheel Assemblies. Contains (4) bearings & (1) wheel bushing. ID 5/8", OD 1-3/8", HT 7/8".

Replaces Dixie Chopper #30218 ID-1", OD-2-7/16", Height-7/8".

Wheel bushing replaces Dixie Chopper 10203. Fits Dixie Chopper wheel assembly 97166. ID - 5/8", OD - 7/8", Length - 1".

Replaces Dixie Chopper # 40222, Exmark #543365, 513508, 303284, John Deere #AM39206. For 9" tank depth. 2-1/4" dia.

Replaces O.E.M. #6092, Length 14-3/8", Center Hole 11/16", Width 2", Thickness .187. (3) blades for 42" cut. (Low Lift)

Replaces O.E.M. #6236, Length 14-1/2", Center Hole 11/16", Width 2-1/2", Thickness .187. For ZTR models 428 & 429 (3) blades for 42" cut. (Low Lift)

Replaces O.E.M. #8688, Length 14-1/2", Center Hole 11/16", Width 2-1/2", Thickness .187. For ZTR models 428 & 429 (3) blades for 42" cut. (High Lift)

Replaces O.E.M. #9229, Length 17", Center Hole 5/8", Width 2", Thickness .204. (3) blades for 50" cut Standard Deck

Replaces O.E.M. #8689, Length 17", Center Hole 5/8", Width 2-1/2", Thickness .187. (3) blades for 50" cut

**LIMITED SUPPLY** discontinued item                                 

Replaces O.E.M. #9265, Length 17", Center Hole 5/8", Width 2-1/2", Thickness .187. For ZTR models 502 & 503 (3) blades for 50" deck (High Lift)

Replaces O.E.M. #1324, Length 18-1/2", Center Hole 3/4", Outside Hole 13/32", Width 2", Thickness .187. For ZTR model 361 only. (2) blades for 36" cut.

Replaces O.E.M. #1352, Length 18-1/2", Center Hole 3/4", Outside Hole 13/32", Width 2-1/2", Thickness .187. For ZTR w/catcher takes (1) DI19L & (1) DI19R for 36" cut (left hand side)

Replaces O.E.M. #1351, Length 18-7/16", Center Hole 3/4", Outside Hole 13/32", Width 2-3/4", Thickness .187. For ZTR 361 w/catcher takes (1) DI19R & (1) DI19L for 36" cut (right hand side)

Replaces O.E.M. #9383, Length 20-1/2", Center Hole 5/8", Width 2-1/2", Thickness .240. (3) blades for 60" cut.

Replaces O.E.M. #9444, Length 17", Center Hole 11/16", Width 2-1/2", Thickness .187. (3) blades for 50" cut. (High Lift)

Replaces O.E.M. #9443, Length 17", Center Hole 11/16", Width 2-1/2", Thickness .187. (3) blades for 50" cut. (Low Lift)

Replaces O.E.M. #9445, Length 20-1/2", Center Hole 11/16", Width 2-1/2", Thickness .240. (3) blades for 60" cut. (High Lift)

Replaces O.E.M. #1765. Models 5421 & 5422 - Box to Hydro -OEM spec belt.

Replaces Dixon #1687. Main drive pulley on Dixon mowers. ID-1/2" OD- 4-1/2" Height-1"

Replaces Dixon #1713. Used on Dixon cone drive models. Plastic. ID-1/2" OD-2" Height-1"

Replaces O.E.M.#6092, 6013, 8600. Length 14-7/16", Center Hole 45/64", Width 2-1/2", Thickness .187, Commercial Mulcher Blade. (3) blades for 42" cut.

Replaces O.E.M. #6897, Length 17", Center Hole 11/16", Width 2-1/2", Thickness .204. Commercial Mulcher Blade (3) blades for 50" cut.

Replaces O.E.M. #6898, Length 20-1/2", Center Hole 11/16", Width 2-1/2", Thickness .204. Commercial Mulcher Blade (3) blades for 60" cut.

Replaces O.E.M. #1684. ZTR 424, 426 - Drive Belt - OEM spec belt. **Limited supply - discontinued item**

Replaces O.E.M. #1714. Drive Belt - fits T-Box-50" Mower-OEM spec belt.

Replaces O.E.M. #1860. Drive Belt - fits model 5421-OEM spec belt. **Limited Supply-- Discontinued item**

Replaces O.E.M. #2412. ZTR 301, 302, 308, 311 - Blade Belt - OEM spec belt.

Replaces O.E.M. #6109. ZTR 421, 424, 426 - Deck Belt - OEM spec belt.

Replaces O.E.M. #1714. Drive Belt - fits T-Box-50" Mower. *This item is not in our current catalog*

Replaces O.E.M. #6109. ZTR 421, 424, 426 - Deck Belt.

Replaces O.E.M. #6111. ZTR 421, 424, 426 - Blade Belt.

Replaces O.E.M. #2412. ZTR 301, 302, 308, 311 - Blade Belt.

Replaces O.E.M. #1300. Models 5421 & 5422-OEM-99.82".

Replaces O.E.M. #1539. ZTR 421, 422 - Drive Belt.

Replaces O.E.M. #6360. ZTR 425 Deck Belt.

Replaces O.E.M. #6361. ZTR 425 Blade Belt.

Replaces O.E.M. #7650. Engine to Trani Belt - OEM spec belt.

Replaces O.E.M. #2469. ZTR 308, 311, 425 - Drive Belt.

Replaces O.E.M. #7725. Engine to Deck Belt - 2301, 3303-3304.

Replaces O.E.M. #1684. ZTR 424, 426 - Drive Belt.

Replaces O.E.M. #1860. Drive Belt - fits model 5421.

Replaces Dixon 8179. Open cage roller bearing with retainer bushings. Fits 42" and 50" cut Dixon ZTR with single are caster wheel. Fits Dixon wheel 8178. ID-1", OD-1-3/8", Length-2-1/2".

Replaces O.E.M. #13031000760. Echo backpack blower model PB400. Length or O.D.- 2-15/16", Thickness or HT. 3/8"HT.

Replaces O.E.M. #13031004922, 13031003060. Echo Trimmers snap on filter. For most trimmers using Kiortz engines. McCulloch #215013/Toro #463960, Hoffco #208645/Poulan 530-091886. 2-7/16" Diam.

Replaces O.E.M. #13031051830. Fits models PAS2400, PB24LN, PAS2601, PE260, SRM2400, SRM2601, SRM2605, SRM3100, ES231, HCA2400, HCA261, and LST2400. Length or O.D. 3-1/16", Width or ID 3-7/64", Thickness or HT 5/16".

Replaces Echo #13031054130. Fits models GT2000, GT1100, GT2400, SRM230 & SRM2100 Trimmers. ES2100, ES2400 Shredd & Vacs. HC1500, HC2000, HC2400, HC2410 Hedge Clippers. Power prunners 2400 Mantis Tillers.

Replaces Echo #A226000031 & A226000032. Fits ECHO PB403, PB413, PB500H, PB500T, PB603, PB620, PB650 and PB 755 blowers 4-1/8" length, 2-3/4" width, 1-1/2" height.

Starter rewind spring replaces OEM#177220 0111 0. Fits model numbers PB-9, 400.

Starter rewind spring replaces OEM#177220 0393 0, Fits model numbers SRM200, 202, 302, 400.

Starter rewind spring replaces OEM#177220 0653 0. Fits model numbers KE140, 200, GT140, 160, 200, F-2/1, 2/2, 2/3, S2A/1, 2A/2, SRM140, SRM210AE.

Replaces Echo OEM# 13031003360. For Echo power blower PB210E, McCulloch #213883, #300385, Poulan #91886, Toro #439730, John Deere PT10281. 4" Length, 2-3/4" Width.

Starter rewind spring replaces OEM#1 177220 4203 0. Fits model numbers GT1100, GT2102, GT2103, SRM1501, SRM2301, SRM2310, SRM2400, Trimmers and Brushcutters. Also fits PB1000 Blowers.

Starter rewind spring replaces OEM#177220 4063 0. Fits model numbers Echo CLS4600, SRM2200, SRM2201, SRM 2501, SRM2502, SRM3000, SRM3001, SRM3800 Trimmers and Brushcutters.

Replaces O.E.M. #13031700760. Fits PB400E backpack blower. Length or O.D.- 7" (L.), Width or I.D. 1-3/4" (I.D.), Thickness or HT. 3-1/4 O.D.

Replaces O.E.M. #13030508360, 13030508361. Fits backpack blower models PFB4600 and PB6000. Length or O.D.- 10-1/2", Width or I.D. 3", Thickness or HT. 1-1/2".

Replaces O.E.M. #13031008260. Fits backpack blower model PB4600. Length or O.D.- 10-1/2", Width or I.D. 3", Thickness or HT. 3/4".

Replaces Echo#130-310-04560. Fits Echo 2400 hedge clipper.

Replaces Echo #130-310-51730. Fits Echo SRM2500 trimmer.

Replaces Echo # 131-004-0632-0. Fits Echo Trimmer model SRM 140 and Blower model PB200 most trimmers equipped with Kioritz engines.

Replaces Echo #131004-40930 and #131004-55730. Fits Echo Trimmers and Home Owner Blowers, models GT, SRM, HC, PB and PE.

Replaces Echo #131004-06610, 13160009860 & 13160009861. Fits Echo blower models 4500 and 4600.

Replaces Echo #131004-48730/131004-55830 and #131004-55730. Fits models SRM2100, HC2400 and SRM2500.

Starter rewind spring replaces Echo 177220-35430. Fits Echo models 3000, 3400 and 3450.

Replaces O.E.M. 178001-4093-0, BC: SRM2500, SRM2501

*Limited supply*

Throttle cable replaces Echo 178001-00761. Fits blower models PB400 and PB400E. Conduit 13-1/2", inner wire 15-1/2", wire travel 2".

Replaces Echo 178001-0963-0. Fits blower models GT140, 160, 160A, 160AE, 200, 200A, 200B, 200BE, 200CE, 1000 & 2100. Conduit 12-1/2", Inner wire 15-3/4", Wire travel 3-1/4".

Vent assembly replaces Echo 131300-56430, 13130040630 & A356000030. Fits model GT1100, 2000, 2100, 2102, 2103, 2400, SRM-1500, 1501, 2100, 2300, 2301, 2400, 2500, 2501, 2510, 3000, 3800, SRS-2100, PE-2400, PB1000/1010, 2400, ES-2000, SHR-2100.

Walbro carburetor fits Echo models # PB400 and PB400E Backpack Blowers. Walbro WA-55A/WA-55B/WA-55-1.

Walbro carburetor fits Echo #PB400. Walbro WT-410-1.

Walbro carburetor replaces Echo model #GT2400. Walbro WT-424-1.

Walbro carburetor replaces Echo # 12300040630. Fits Echo models #SRM2000, SRM2200 and GT22000 trimmers and hedge trimmers. Walbro WY-18.

Walbro carburetor replaces Echo #12300057730 & 12300057731. Fits model SRM2601 trimmers. Walbro WYJ-192/WYJ-192-1.

Walbro Carburetor fits Echo model # SRM2601. Walbro WYJ-220-1.

Zama carburetor replaces Echo #12520008261. Fits PB4600 blowers. Zama C1M-K24B.

Zama carburetor fits Echo models #PB602, PB603, PB610 and PB611. Zama C1M-K49C.

Replaces Echo #1250050630. Fits models GT2103, SRM1501. Zama C1U-K16A.

Replaces Echo #12520051231. Fits models SRM2501 and John Deere 25S trimmers. Zama C1U-K20C.

Replaces Echo # 12520052131. Fits models SRM2400, SRM3800, GT2400 and John Deere 38B trimmers. Zama C1U-K23B.

Zama carburetor fits Echo models #PB2100. Zama C1U-K42B.

Zama carburetor fits Echo model #HC1500, HC1600, HC2000, HC2410, HC2400 and HCR1500. Zama C1U-K51.

Zama carburetor fits Echo models #SRM2100, GT2000, GT2100, ST2000SB, PAS and PDSR. Zama C1U-K52.

Zama carburetor fits Echo model #TC2100. Zama C1U-K54A.

Zama carburetor fits Echo models #GT200, GT201, SRM200, SRM201, SRM130, SRM231, HC160, HC180 and HC200. Zama RB-K66A, RB-K70A.

Contains 300 pieces from 1/16"-7/8".

Balanced blades give your mowers a smoother cut and less wear on equipment! Compact and easy to use. Inexpensive

Replaces O.E.M # 237001, 696015-52631. Length 7-11/16", Center Hole 1", Width 2", Thickness .095, Replaces: Green Machine 237001. Fits Edger Tool #2851. Shindaiwa model #LE-20 also Echo 696015-52631 model PE2400.

Also see our EBU8 for thicker edger blade

Replaces O.E.M# 2059-HD-10. Length 10", Center Hole 1/2", Width 2", Thickness .150, Used on many Commercial Edgers. Sharpened 4 sides. Fits Little Wonder, Tanaka, McLane #2059-HD-10.

Length 10", Center Hole 5/8", Width 2", Thickness .125, Tapered, sharpened four sides.

Replaces O.E.M.# 237001. Length 8" diameter, Center Hole 1", Thickness .095, Replaces Green Machine 237001. Edger Tool 2851. Also fits Echo model PE2400 and Shindaiwa model LE-20.

Replaces O.E.M # 530095086. Length 8-1/2", Center Hole 9/16" "D" shape center hole, Width 1-1/2", Thickness .120, Replaces Weedeater 530095086. Fits gas powered edgers.

Length 9", Center Hole 1/2", Width 2", Thickness .117, Tapered, sharpened four sides.

Length 9", Center Hole 1/2", Width 9", Thickness .180, Star Blade 4 points.

Length 9", Center Hole 5/8", Width 9", Thickness .180, Star Blade 4 points.

Length 9", Center Hole 1/2", Width 9", Thickness .180, Star Blade 8 points.

Length 9", Center Hole 5/8", Width 2", Thickness .117, Tapered, sharpened, four sides.

Length 10", Center Hole 1/2", Width 2", Thickness .125, Unsharpened.

Replaces O.E.M #840084, 216062, 4133-713-4101, 720-237-001, 613223. Length 7-11/16", Center Hole 1", Width 2", Thickness .125, Fits Maruyama, Ryobi, Green Machine, Echo, Shindaiwa, and Stihl. Long lasting heat treated.

Electric PTO clutch replaces Exmark OEM#s 1-611223 & 603539.  Also replaces Scag OEM#s 48786, 481633 and Warner # 5215-13.  1" Bore, 6" pulley.  Uses A/B belt. Fits SSZ & STHM models.  Confirm O.E.M.# prior to ordering.  25% restocking fee on all returned Electric PTO Clutches.

Electric PTO clutch replaces Exmark 1-551054, 1-543259, fits turf ranger models. Also replaces Great Dane D18000, AYP 106316, 109550X, Bobcat 188019, Ferris 1521083, Husqvarna 917063, Snapper 17063. Warner 5215-14. 1" IDx 6" pulley.  A/B Belt type.  Confirm O.E.M.# prior to ordering.  25% restocking fee on all returned Electric PTO Clutches.

410/350-4, Polyurethane Sawtooth Tire - No flat tire. Must have a split rim to use this tire.

400-8, Polyurethane Ribbed Tire - No flat tire. Must have a split rim to use this tire.

Size: 11 x 400 x 5. Polyurethane Smooth Tire - No flat tire. Must have a split rim to use this tire.

480/400-8, Polyurethane Ribbed Tire - No flat tire. Must have a split rim to use this tire.

Size: 13x500x6. Polyurethane Ribbed - No flat tire. Must have a split rim to use this tire.  *Limited supply*

8x300-4, Polyurethane Smooth Tire - No flat tire. Must have a split rim to use this tire.

9x350-4, Polyurethane Smooth Tire - No flat tire. Must have a split rim to use this tire.

9x350-4, Polyurethane Traction Tire - No flat tire, used on OUR 9354DB-U-V wheel.  Must have a split rim to use this tire.

280/250-4, Polyurethane Sawtooth Tire - No flat tire. Must have a split rim to use this tire.

Uncorded, single pack. Elvex Blue is a plug for today's demands. It meets the requirements of both users and safety and health professionals. Excellent attenuation, 32NRR. High level of hygiene. Visually easy to monitor. One size fits all, easy to insert. Slow expansion time for early insertion. Comfortable low pressure foam. Easy to read usage instructions, in English, Spanish, and French. Good sound reduction properties.

Corded, Case of 100 pairs.  Elvex Blue is a plug for today's demands. It meets the requirements of both users and safety and health professionals. Excellent attenuation, 32 NRR. High level of hygiene. Visually easy to monitor. One size fits all. Easy to insert. Slow expansion time for early insertion. Comfortable low pressure foam. Easy to read usage instructions, in English, Spanish, and French. Good sound reduction properties.

Corded, single pack.  Elvex Blue is a plug for today's demands. It meets the requirements of both users and safety and health professionals. Excellent attenuation, 32 NRR. High level of hygiene. Visually easy to monitor. One size fits all, easy to insert. Slow expansion time for early insertion. Comfortable low pressure foam. Easy to read usage instructions, in English, Spanish, and French. Good sound reduction properties.

Full case of 200 pair, uncorded ear plug. Elvex Blue is a plug for today's demands. It meets the requirements of both users and safety and health professionals. Excellent attenuation, 32NRR. High level of hygiene. Visually easy to monitor. One size fits all, easy to insert. Slow expansion time for early insertion, comfortable low pressure foam. Easy to read usage instructions, in English, Spanish, and French. Good sound reduction properties. Uncorded, Case of 200 pairs.

Elvex QuieTunes earmuffs with a built-in FM stereo radio offers the following features: Hearing protection is the primary objective and QuieTunes provides 25dB Noise Reduction Rating. An electronic control limits the sound produced inside the headset to 82 dB. QuieTunes comes with a charger, allowing the unit to recharge overnight for 40+ hours of use.

**LIMITED SUPPLY**

Elvex Faceguard features lightweight design for safety and comfort when using a saw or line trimmer. Nylon mesh screen is much cooler and allows air circulation. The headband and crown strap adjust by pinlocks and the pivoting browguard can easily be adjusted even with gloves on! Now with built-in sweat band! Comes complete with mesh screen.

SuperSeal ear cushions for long term comfort. A soft cushioned headband. Low headband force for great comfort. Self-aligning suspension, and easy adjustment. Noise Reduction Rating is 28 dB NRR, achieved at an independent, certified laboratory. Dielectric construction. Sophisticated design and durable materials. Best price in its performance class.

Elvex SuperSonic muff is one of only a few ear muffs that have achieved a 29 dB NRR rating at an independent and certified laboratory in accordance with ANSI S3.19-1974. The SuperSonic muff has the lowest weight in its class, 8.9 oz. SuperSonic has the lowest headband force in its class. SuperSeal ear cushions provide outstanding seal and comfort. A dielectric construction for environments with exposure to high voltage situations.

Quattro is a universal size reusable ear plug, designed to be used over and over again, with maintained comfort and effectiveness. Elvex Quattro offers the following features:

• A four flange design that allows this ear plug to fit almost all ear canals.

• An ultra-soft polymer provides a comfortable and effective seal.

• A sturdy and stiff handle that allows an easy grip for insertion and removal.

• Material is resistant to ear wax and body oils and will outlast PVC ear plugs by many months.

• Polymer is non-allergenic and non-irritating to the sensitive skin in the ear canal.

• Noise Reduction Rating is 25 dB, and the test was performed to ANSI S3.19-1974 at an independent 

• and certified laboratory. See test data below.

• European Single Number Rating is 26 dB, and testing was performed at an independent and certified laboratory. See test data to EN-352-2 below.

• Quattro is available in five versions, corded and un-corded, and packaged in poly-bag or handy plastic container, as well as in a metal detectable version. 

• Quattro has been assigned U.S. Military national stock numbers.

single pair Corded Quattro ear plugs with plastic case & chain. See our EP412 for complete description

Elvex Ranger Safety Glasses are loaded with features which translate into a safe, comfortable, and stylish product. Fashionable design allows an uninterrupted field of vision. Polycarbonate lens provides optical clarity and impact resistance complies with  the ANSI Z87.1-2003 & CE EN-166 standard. Side and top protection are built in to provide additional safety margin. Nose and ear piece design offers snug and secure fit, even over most prescription glasses. 99% of harmful ultraviolet light is filtered out. Amber for overcast days.

Elvex Ranger Safety Glasses are loaded with features which translate into a safe, comfortable, and stylish product. Fashionable design allows an uninterrupted field of vision. Polycarbonate lens provides optical clarity and impact resistance complies with  the ANSI Z87.1-2003 & CE EN-166 standard. Side and top protection are built in to provide additional safety margin. Nose and ear piece design offers snug and secure fit, even over most prescription glasses. 99% of harmful ultraviolet light is filtered out. Clear for neutral light.

Elvex Ranger Safety Glasses are loaded with features which translate into a safe, comfortable, and stylish product. Fashionable design allows an uninterrupted field of vision. Polycarbonate lens provides optical clarity and impact resistance complies with  the ANSI Z87.1-2003 & CE EN-166 standard. Side and top protection are built in to provide additional safety margin. Nose and ear piece design offers snug and secure fit, even over most prescription glasses. 99% of harmful ultraviolet light is filtered out. Grey for bright light.

Elvex Ultra Lite Ear Muffs are 25DB NRR rated. Extremely light, they weigh only 6.8 oz. and are a great value! Blue.

Replaces Encore #363216 and Ferris #1520814. Fits 32", 36", 48" and 61" cut decks. Taper lock single pulley. 5-3/4"OD. Use with our S275840 pulley hub. For A and B belts.

Replaces O.E.M. #603015. 60" LH Deck.

Replaces O.E.M. #603016. 60" RH Deck.

Replaces O.E.M. #523106. Pump Belt.

Replaces O.E.M. #483035, 483024, Length 16-1/2", Center Hole 5/8", Width 2-1/2", Thickness .204. (3) blades for 48" cut, (2) blades for 32" cut.

Length 16-1/2", Center Hole 5/8" Width 3", Thickness .204 (3) Blades for 48" cut (2) blades for 32" cut (High Lift).

Replaces O.E.M. #363291, 482306, 363046. Length 18", Center Hole 5/8", Width 2-1/2", Thickness .204. (2) blades for 36" cut, (3) blades for 52" cut.

Replaces O.E.M. #363046, Length, 18", Center Hole 5/8", Width 3", Thickness .204 (2)blades for 36" cut, (3) blades for 52" cut. (High Lift).

Replaces O.E.M. #523349. 61" Engine to Deck Belt.

Encore Catcher. Heavy duty military spec. latch, Curved front directs grass to back of catcher for high density packing, Non vented front construction of catcher keeps grass from clogging mower outlet, Weighs 19.5# and holds 3.3 cubic feet. Tubular steel frame continuous weld superior to spot-weld catchers, 22 gauge solid and perforated sheet steel.

Encore Jumbo Catcher Heavy duty military spec. latch, Curved front directs grass to back of catcher for high density packing, Non vented front construction of catcher keeps grass from clogging mower outlet. Jumbo weighs 23# and holds 4.3 cubic feet. Tubular steel frame continuous weld superior to spot-weld catchers, 22 gauge solid and perforated sheet steel.

Replaces O.E.M. #363312 Belt - OEM spec. belt

Replaces O.E.M. #483030. 48" Main Belt - OEM spec belt.

Replaces O.E.M. #483031. 48" Blade to Blade Belt (short) - OEM spec belt.

Replaces O.E.M. #483030. 48" Main Belt.

Replaces O.E.M. #483031. 48" Blade to Blade Belt (short).

Replaces O.E.M. #363210. 36" Main Belt - Deck Belt.

Replaces O.E.M. #363212. Transmission Belt.

Replaces O.E.M. #523107. 52" Engine to Deck Belt - OEM spec belt.

Replaces Encore O.E.M.#523025 and 523370. Also replaces Warner #5215-69. Pulley 6", Height 3-1/2", Bore 1-1/8". Uses 5/8" belt. Confirm O.E.M.# prior to ordering. 25% restocking fee on all returned Electric PTO Clutches.

Replaces Encore #483025. Heavy-duty style. 3/8"ID x 5"OD x 7/8" Ht. 5/16" offset reducer bushing.

Replaces Encore # 363191. Fits rear drive wheel 36", 48",52" and 61". 2-9/32"ID x 8"OD. Four 11/32" mounting holes, 2.65" center to center.

Replaces Encore #363137. Jackshaft wheel drive pulley for walk behind units. 5/8"ID x 3-1/4" OD. 3/16" keyway. 5/16"-18 set screw. Double pulley.

Replaces Encore #363217. Taper lock hub for our S275-945 pulley. 1" bore. 1/4" keyway.

Replaces Encore #363168. Heavy duty style. Fits 36", 48", 52" and 61". 3/8"ID x 5-1/4"OD x 1-1/2"Ht. Includes 3/8" offset, 3/8" flush and 1/2" offset reducer bushings.

Replaces Encore/Ferris 15E363268, 363268 & 363203. Fits older style models BG36KA, BG48KA, BG52KA, GD36KA, GD8K. Cinduit 36 -1/2", Inner wire 41-1/4", Wire travel 1-3/4".

Replaces Exmark 362095 and Snapper 76398. ID- 1", OD- 5-5/8", Height- 1-5/16", Keyway- 1/4".

 

Ariens Blade replaces OEM# 04916400. Also replaces Gravely # 4916400 and Exmark 1-303527. 18"Length, 5/8"Center Hole, 2.5"Width, .204 Thick. (3) blades used for 52" cut.

Replaces O.E.M.# Exmark 513211, 1-513211 & 109-4180. Also fits Bobcat 2188179, Bunton PL7488, Dixie Chopper 60105, 68140, Dixon 5565, 7252, 501, 502, 5501, 5017, 5020, 5023, 5421, 5601, Encore 423063 & 423361, Ferris 22028, Honda 25641-VE4-003, Husqvarna 539102606, Kees 102606, 101164, Toro E633750 & 23-9740. Transmission filter has 3/4"-16 thread, 10 Micron, 3-1/2" Height, 3" O.D.

Excel - Hustler blade replaces OEM# 798496.  3 blades used for 66" cut.  Length- 22-1/2", Width- 3", Centerhole- 5/8", Thickness- .204".

 

Replaces O.E.M. #781898, Length, 17-7/8", Center Hole 5/8", Width 3", Thickness .240 (3)Blades for 52" cut. Fits models Hustler Z, Super Z and Short Cut.

Replaces O.E.M. #782516, Length, 21", Center Hole 5/8", Width 3", Thickness .240 (3)blades for 60" cut. Fits models Hustler Z, Super Z and Short Cut.

Replaces O.E.M. #770339, Length 19", Center Hole 1/2", Width 2-1/2", Thickness .204. (3) blades for 54" cut. Fits 54" cut Excel short cut.

Replaces O.E.M. #767111, Length 16-31/32", Center Hole 1/2", Width 2-1/2", Thickness .204. (3) blades for 48" cut. Fits 48" cut Excel short cut.

Replaces O.E.M. #754879, Length 23-7/8", Center Hole 1/2", Width 2-3/4", Thickness .240. Fits 72" heavy duty dual trim deck takes (2) EXL6628 & (1) EXL6728. Also fits Range Wing mowers takes (4) EXL6628 & (3) EXL6728

Replaces O.E.M. #754853, Length 23-7/8", Center Hole 1/2", Width 2-3/4", Thickness .240. Fits models 2500, 72" deck 275, 285, 295, 305, 320, 340, 400, 3000, 3200, 3400, 4100, 4200, 4300, 4400, 4420, 4500, 4600 units with 72" "Three Way Deck" or "Quad Cycler" deck

Replaces O.E.M. #715078, Length 21-15/16", Center Hole 33/64", Width 2-3/4", Thickness .204. Fits model 260K compact unit with 60" deck only.  **LIMITED SUPPLY**

Replaces O.E.M. #030866, Length 17-7/8", Center Hole 33/64", Width 2-3/4", Thickness .187. (3) blades for 51" cut. Fits model 251K compact with 51" deck

Replaces O.E.M. #076752, Length 21", Center Hole 33/64", Width 2-3/4", Thickness .204. (3) blades for 60" cut. Fits model 2500 with 60" cut and Excel outfront mowers with a 60" deck

Replaces Excel O.E.M. #031997. Also replaces Cub Cadet 734-3058B, Ariens 03471700, AYP 133957, MTD 734-3058B, Murray 92265 and Simplicity 1700184. Wheel size 5" x 2.75". Plastic heavy duty deck wheel for 38", 40" and 50" cut decks. 2-1/2" offset with 1/2" bore.

High-lift blade replaces Excel/Hustler OEM#s 795526 & 783753.  3 blades used for 52" cut.  Fits Super Z.  Length- 17-7/8", Width- 2-1/2", Centerhole- 5/8", Thickness- .204. 

Replaces O.E.M. #783977, Length 24", Center Hole 5/8", Width 3", Thickness .240. (3) blades for 72" cut. Fits Super Z.

Replaces O.E.M. #784256, Length, 15-5/8", Center Hole 5/8", Width 2-1/2", Thickness .204 (3)blades for 44" cut, Fits models Hustler Z, Super Z and Short Cut.

Replaces Exmark 403032 and Snapper/Kees 76648. ID 1", OD- 5-3/4", Height 2-13/64", Keyway- 1/4"

 

Replaces Exmark 303498. Fits 36" commercial walk behind mowers. Uses A 5/8" belt. ID- 1", OD- 6-1/4, Height- 1-1/4", Keyways- 1/4".

Replaces Exmark 323285. Also replaces Yazoo Kees 639-19087. ID- 3/8", OD- 2-3/4", Height- 1-3/8".

Replaces Exmark 603805. Deep V Idler pulley. Fits Lazer Z. ID 11/16", OD- 5", Height 7/8".

Replaces Exmark 633166. ID- 11/16", OD- 6", 1-1/8".

Replaces Exmark 633167. Pump drive belt idler for Lazer Z model. ID- 3/8", OD- 3-1/8", Height- 1-3/16".

Replaces Exmark #302036. Fits 32" & 48" variable and 5 speed decks (left side).

** LIMITED SUPPLY, DISCONTINUED ITEM **

Drive pulley replaces Exmark 322172. Includes brake drum and 2 pulleys. ID- 2-1/4", OD- 8", Height- 1/2".

Replaces Exmark #302037. Fits 32" & 48" variable and 5 speed decks (right side).

** LIMITED SUPPLY, DISCONTINUED ITEM **

Replaces Exmark 323070. Fits 36", 48", & 52" cut, 5 speed Viking & Metro series, commercial midsize Walkbehind Mowers. Cast iron pully.

Replaces Exmark 323256. Fits 36" & 48" walk behind mowers. Uses 1/2" belts. ID- 1", OD- 2-3/4", Height- 1-1/8", Keyway 1/4".

Replaces Exmark 303464. Fits Exmark 48" mid size. ID- 1-21/32", OD- 9", Height- 13/16"

Replaces Exmark O.E.M.# 103-0665, 1-641300 and Scag #481530, 461395 & 461716. Pulley 6", Height 2-3/4", Bore 1-1/8". Fits Lazer Z models. Ogura GT2.5-MC04/MA-GTEXM14Z. Confirm O.E.M.# prior to ordering. 25% restocking fee on all returned Electric PTO Clutches.

Front Wheel Spacer replaces Exmark #1-633581. Fits Exmark Laser Z units. Used on our 656DC4-562SM and 506DC4-562SM wheel assemblies. Also replaces Scag # 43584. Spacer for Front Wheel, Bearing and Seal. ID-3/4", OD-1-1/8", Width - 5/8".

Spacer replaces Exmark #1-633959. Fits Exmark Laser Z 13x650x6 wheels. Used with our WEX10075 wheel assembly. ID-1/2", OD-3/4", Length - 7-1/2". 

Also replaces Scag 43583

Replaces Exmark OEM# 103-0206 and Toro 104-2541 & 88-9830.  Fits Lazer Z XP 60" & 70".  3 position, 6 terminals

Replaces Exmark #523328, 1-523328, fits Lazer Z models. Also replaces Toro #1-523328, fits Z Master models. Confirm O.E.M.# prior to ordering. 25% restocking fee on all returned wheel motors.

Replaces O.E.M. #633582, 634662, Wheel size 13x500-6, 4-ply smooth tire on 1-piece white wheel, 5-5/8" center, 3/4" HS tapered bearings, seals, and spacers included to assemble. Fits Lazer Z and Toro Z Master. Uses our spanner WB10017.

Wheel size 13x650-6, 4-ply smooth tire on 1-piece white rim. 5.625" center, 3/4" HS bearing with beadlock.

Replaces O.E.M. #513648, Wheel size 9x350-4, 4-ply smooth tire on 1-piece white wheel, 4-1/2" CTR, 3/4" open cage roller bearing.

Replaces O.E.M. #913648 & 513648. 9x350-4 smooth Eliminator flat-free tire on white rim, 3/4" OCRB, 4-1/2" centered hub with Zerk. Uses our 9354-U275-SM Eliminator tire.

Replaces Exmark belt OEM# 103-4014. Mule drive belt. Fits ZTR 60" & 72" cut. OEM spec belt

Replaces Exmark belt OEM# 103-6906. Pump drive belt, fits Lazer Z serial #s 540,000 & higher. OEM spec belt

Deck belt replaces Exmark OEM# 323733 on 36" Walkbehind Metro SN 22000 >.  OEM spec. belt.

Notched Hi-lift blade replaces Exmark OEM# 103-6402. 2 blades used for 36" cut, 3 for 52" cut. 18" length, 2-1/2" width, 15/16" center hole, .204 thick.

Exmark bottom spindle spacer repaces OEM# 1-633573.

Replaces #323261, 2-1/4" I.D. x 6" O.D. x 1-1/4" HT. Fits Metro Units.

Commercial mulching blade replaces Exmark OEM# 103-6398. 20-1/2" length, 15/16" centerhole, 2-1/2" width, .204 thickness.  3 blades used for 60" cut.

Caster Yoke replaces Exmark #1-322145-01. Fits Metro and Viking walk behinds with serial 102000 and higher.

Front Caster Yoke Bearing Seal replaces Exmark #543511. ID 1-1/4", OD 2", width 1/4". Sold individually

Caster support arm replaces Exmark 30211. Also replaces Encore 362007 and Jacobsen 55366, and Jacobsen 182595.  **Limited Supply--discontinued item** 

Caster yoke replaces Exmark 302200.  **Limited Supply--discontinued item** 

4-1/2" yoke replaces Exmark 522143. Fits models Turf Ranger & Turf Tracer 52" & 60" cut and Explorer 44 & 52" cut models.

Caster yoke replaces Exmark 302108 & 302104. Fits Exmark/Jacobsen crew chief 36" and 48" decks. Used with 10" pheumatic wheel assembly.

Replaces Exmark 303514, 303044, Snapper 76514, and Kees 363194. ID-7/8", OD-1-1/8", Height-1-1/4", Flange OD-1-1/2".

Replaces O.E.M. #633483, Length 20-1/2", Center Hole 5/8", Width 2-1/2", Thickness .240. (3) blades for 60" cut (High Lift for wet grass) Fits Lazer Z or Turf Ranger newer models.

Replaces O.E.M. #543396. Wheel size 20x1000-8, 4 ply super turf tire on 4 hole rim.

Replaces O.E.M. #603714, Wheel size 16x650-8, 16x650-8/4-ply traction tire on 4 hole, 4" BC rim.

Replaces O.E.M. #603627, Wheel size 16x750-8, 16x750-8/4-ply traction tire on 4 hole, 4" BC rim.

**limited supply, call for availability**

 

Drive shaft replaces Exmark 323502. Fits 5 speed mowers. 9-spline. Used with our MP9579 coupler.

Replaces O.E.M. #612111 & 103-2510. Length, 20-1/2", Center Hole 5/8", Width 2-1/2", Thickness .204 (3) blades for 60" deck. Low Lift Sand Blade.

Replaces O.E.M. #603045.  60",  Blade Belt.

Replaces O.E.M. #603306. Turf Tracer 60" Engine to Deck Belt.

Replaces O.E.M. #603576.  52" Blade Belt.

Replaces O.E.M. #103-1577, Length, 16-1/4", Center Hole 5/8", Width 2-1/2", Thickness .204 (2)blades for 32" cut, (3) blades for 48" cut. Solid Air Foil Hi-Lift.

Replaces O.E.M. #103-1579, Length, 15-1/4", Center Hole 5/8", Width 2-1/2", Thickness .204 (3) blades for 44" cut. Solid Air Foil Hi-Lift.

Replaces O.E.M. #103-0881. Lazer Z. Mule Drive Belt fits Lazer XP- OEM spec belt.

Replaces O.E.M. #103-0882. Lazer Z. Pump Drive Belt fits Lazer ZXP- OEM spec belt.

Replaces Exmark O.E.M. #1-303527. Also replaces Airens 04916400 and Gravely 4916400. Length 18", Center Hole 5/8", Width 2-1/2", Thickness .204. (3) blades for 52" cut. High Lift blade. Fits Lazer Z.

Exmark pump drive belt replaces OEM# 103-4761.  Fits Lazer Z HP.  OEM spec. belt

 

Replaces Exmark #1-323262. Fits Metro walkbehind mowers.

Replaces Exmark O.E.M. #103-2530 and Toro # 105-7718. Length 20-1/2", Center Hole 5/8", Width 2-1/2", Thickness .204. (3) blades for 60" cut. Notched High Lift Blade.

Replaces O.E.M. #653438. Blower Belt - OEM spec belt.

Replaces O.E.M. #103-2507. Length 16-1/4", Center Hole 5/8", Width 2-1/2", Thickness .204. (3) blades for 48" cut. Low Lift Blade.

Replaces O.E.M. #103-2508. Length 18", Center Hole 5/8", Width 2-1/2", Thickness .204. (3) blades for 52" cut. Low Lift blade.

Replaces O.E.M. #1-613271. Turf Tracer. Pump Drive Belt - OEM spec belt.

Replaces O.E.M. #1-413095. Turf Tracer & Viking Hydro. Pump Drive Belt - OEM spec belt.

Replaces O.E.M. #103-0301. Length 20-1/2", Center Hole 5/8", Width 3", Thickness .204. (3) blades for 60" cut. Mulching blade.

Replaces O.E.M. #103-6403. Length 20-1/2", Center Hole 15/16", Width 2-1/2", Thickness .204. High Lift blade. (3) blades for 60" cut. Notched Air Lift blade.

Replaces O.E.M. #103-6404. Length 24-1/2", Center Hole 15/16", Width 3", Thickness .204. Fits 72" lazer model. (3) blades for 72" cut. Air Foil Lift blade.

Replaces O.E.M. #103-6401. Length 16-1/4", Center Hole 15/16", Width 2-1/2", Thickness .204. Notched air foil blade. (3) blades for 48" cut. High Lift blade. Wrong picture is shown in our 2006 catalogs, this is the correct picture.

Replaces O.E.M. #103-6391. Length 16-1/4", Center Hole 15/16", Width 2-1/2", Thickness .204. (3) blades for 48" cut. Mulching blade.

Replaces O.E.M. #103-6392. Length 18", Center Hole 15/16", Width 2-1/2", Thickness .204. (2) blades for 36" cut. (3) blades for 52" cut. Mulching blade.

Replaces O.E.M. #103-6393. Length 20-1/2", Center Hole 15/16", Width 3", Thickness .204. Fits Lazer model. (3) blades for 60" cut. Mulching blade.

Replaces O.E.M. #103-6394. Length 24-1/2", Center Hole 15/16", Width 3", Thickness .204. Fits 72" Lazer model. (3) blades for 72" cut. Mulching blade.

Replaces O.E.M. #103-6383. Length 20-1/2", Center Hole 15/16", Width 2-1/2", Thickness .240. Air foil blade. (3) blades for 60" cut. High Lift blade.

Replaces O.E.M. #103-6397. Length 18", Center Hole 15/16", Width 2-1/2", Thickness .204. (3) blades for 52" cut. Commercial Mulching blade.

Replaces O.E.M. #103-6400. Length 15-1/4", Center Hole 15/16", Width 2-1/2", Thickness .204. Notched air foil blade. (3) blades for 44" cut. High Lift blade blade.

Medium lift blade replaces Exmark OEM# 103-9607.
3 blades used for 56" cut
Length 19-1/2", Center Hole 15/16", Width 3", Thickness .204"

Replaces Exmark OEM# 103-8396.  Medium lift blade.  3 blades used for 60" cut.  20-3/4" length, 15/16" center hole, 3" wide, .204 thickness. 

Replaces Exmark OEM# 103-8107.  Mulching blade.  3 blades used for 60" cut.  20-3/4" length, 15/16" center hole, 3" width, .204 thickness

Replaces Exmark OEM# 103-9619.  Medium lift blade.  3 blades used for 66" cut.  22-3/4" length, 15/16" center hole, 3" width, .204 thickness

High lift blade replaces Exmark OEM# 103-8251.
3 blades used for 46" cut
Length 16-1/4", Center Hole 15/16", Width 3", Thickness .204

Replaces Exmark OEM# 103-9606.  High Lift blade.  3 blades used for 56" cut. 

Length 19-1/2", Centerhole- 15/16",  Width- 3", Thickness- .204. 

Replaces Exmark OEM# 103-8244.  High lift blade. 20-3/4" length, 15/16" center hole, 3" wide, .204 thickness.  3 blades used for 60" cut.

Replaces Exmark OEM# 103-9618.  High lift blade.  3 blades used for 66" cut.  22-3/4" length, 15/16" center hole, 3" wide, .204 thickness.

Replaces O.E.M. #103-1297. Lazer Z. Pump Drive Belt fits Lazer ZXP-OEM spec belt.

Replaces Exmark O.E.M. #s 403059, 103-2527 & 103-6583. Also fits Gravely 04919100.  Length 16-1/4", Center Hole 5/8", Outside Hole 11/32", Width 2-1/2", Thickness .240. Heavy Duty (3) blades for 48" cut, (2) blades for 32" cut.

Replaces O.E.M. #403026, Length 16-1/4", Center Hole 5/8", Outside Hole 1/4", Width 2-1/2", Thickness .150. (3) blades for 48" cut.

Replaces O.E.M. #403086, 403148, 103-2517 & 103-6581. Length 16-1/4", Center Hole 5/8", Width 2-1/2", Thickness .160. (3) blades for 48" cut. Mulching Blade

Replaces Exmark O.E.M. #s 303283, 633482 & 103-2528. Also fits Toro # 105-7781. Length 18", Center Hole 5/8", Width 2-1/2", Thickness .240. Heavy Duty (2) blades for 36" cut, (3) blades for 52" cut.

Replaces O.E.M. #303146, Length 18", Center Hole 5/8", Outside Hole 1/4", Width 2-1/2", Thickness .150. (2) blades for 36" cut, (3) blades for 52" cut.

Replaces O.E.M. #603873, Length 17-29/32", Center Hole 1/2", Width 2-1/2", Thickness .204. (3) blades for 52" cut. Mulching blade "Turf Tracer", Turf Runner Explorer and Lazer Z.

Replaces O.E.M. #303495. Length 17-15/16", Center Hole 5/8", Width 2-1/2", Thickness .160. (2) blades for 36" cut. (3) blades for 52" cut. Mulching blade

Replaces O.E.M. #603844, 603637, Length 18", Center Hole 1/2", Width 2-1/2", Thickness .204. (3) blades for 52" cut. Low Lift. Fits model FMD52.

Replaces O.E.M. #633484, 103-2518 & 103-6582. Length 17-29/32", Center Hole 5/8", Width 2-1/2", Thickness .204. (3) blades for 52" cut. Mulching blade. Fits 52" cut Lazer Z.

Replaces O.E.M. #603661, Length 20-1/2", Center Hole 1/2", Width 2-1/2", Thickness .204. (3) blades for 60" cut. Low Lift fits model FMD60.

Replaces O.E.M. #603874, Length 20-1/2", Center Hole 1/2", Width 2-1/2", Thickness .204. (3) blades for 60" deck. Mulching blade for Explorer, Lazer Z, and Turf Tracer.

Replaces O.E.M. #613112, Length 20-1/2", Center Hole 5/8", Width 2-1/2", Thickness .204. (3) blades for 60" cut. Mulching blade, fits 60" Lazer Z.

Replaces O.E.M. #603283, Length 20-1/2", Center Hole 1/2", Width 2-1/2", Thickness .204. (3) blades for 60" deck. Standard high lift for models Explorer, Explorer II, Turf Ranger & Turf Tracer with 1/2" centerhole.

Replaces O.E.M. #323200.  36" Engine to Deck Belt.

Replaces O.E.M. #323225.  Pump Drive Belt.

Replaces Exmark O.E.M. #1-403174. Fits Metro 48" Blade Belt- M4815KC.  OEM spec belt.

Replaces O.E.M. #413093. Turf Tracer Blade Belt - 48".  OEM spec. belt

Replaces Exmark O.E.M. #1-413094.  36" Deck Drive Belt, HP Model. OEM spec belt

Replaces Exmark O.E.M. #1-413096. Turf Tracer 52" Blade Clutch Belt - TTHP Model - OEM spec belt

Replaces O.E.M. #1-413308. Lazer Z. Blade Drive Belt fits 48" Lazer HP and 52" Turf Ranger deck belt- OEM spec belt.

Replaces O.E.M. #323051. Single V Wheel Drive Belt Cogged - OEM spec belt.

Replaces O.E.M. #543548. Transmission Belt

Replaces Exmark O.E.M. #603809.  52" & 60" Hydro Blade/Blade Belt

Replaces O.E.M. #1-633162. Lazer Z. Pump Drive Belt - 8 Rib - fits Lazer Z- OEM spec belt.

Replaces O.E.M. #633366. Fits Lazer Z - 52" Deck - OEM spec belt

Replaces O.E.M. #513972, Length 10", Center Hole 1/2", Width 2-1/2", Thickness .187. Sweeper blade. For 52" Exmark Explorer. Used with our EX6406 & EX6407 blades.

Replaces O.E.M. #513876, Length 26", Center Hole 1/2", Width 2-1/2", Thickness .204. Fits right hand side of Exmark Explorer 52" cut. Left hand cutting edge.  Use with our EX6405 & EX6407 blades

Replaces O.E.M. #513875, Length 26", Center Hole 1/2", Width 2-1/2", Thickness .204. Fits left hand side of Exmark Explorer 52" cut. Right hand cutting edge. Use with our EX6405 & EX6406 blades.

Replaces O.E.M. #643052. Lazer Z. Deck Belt for 72" Cut- OEM spec belt

Replaces Exmark O.E.M.#s 643006 & 103-2531. Also replaces Toro # 105-7784. Length -24-13/32", Center Hole - 5/8", Width - 3", Thickness - .204. (3) blades for 72" cut. Fits Lazer Z.

Replaces O.E.M. #1-653163 & 103-4760. Lazer Z. Pump Drive Belt fits 44" & 48" Lazer ZHP- OEM spec belt.

Replaces O.E.M. #653368 Lazer Z Mule Drive Belt- OEM spec belt.

Belt replaces O.E.M. #1-653416. Raw Edge belt.  Pump Drive Belt fits 52" Lazer HP- OEM spec belt.

Replaces O.E.M. # 653102 & 103-2519. Length 15-1/4", Center Hole 5/8", Width 2-1/2", Thickness .204. (3) blades for 44" cut. Mulching blade.

Replaces O.E.M. #653101, & 103-2529. Length 15-5/16", Center Hole 5/8", Width 2-1/2", Thickness .204. (3) blades for 44" cut. (High Lift)

Replaces O.E.M. #513264, Length 7", Center Hole 1/2", Width 2-1/2", Thickness .160. Sweeper blade. For 44" cut Exmark ZTR.

Replaces O.E.M. #323299.  48" Engine to Blade Belt - OEM spec. belt

Replaces O.E.M. #323280. Engine to Gear Box - OEM spec belt.

Replaces O.E.M. #633173. Lazer Z, 52" & 60" Engine to Deck Belt - OEM spec belt.

Replaces O.E.M. #633127. Lazer Z, 60" Deck Belt - OEM spec belt.

Replaces O.E.M. #323288.  Double Wheel Drive Belt - OEM spec belt.

Replaces O.E.M. #523541, Exmark 523541, Toro E63-3752, Dixon 7252, Dixie Chopper 68140. Hydrostatic transmission filter has 3/4"-16 thread, 40 Micron, 3-7/8 height, 3" O.D. This item is not in our current catalog, but can still be ordered

Replaces O.E.M. #603283. Length 20-1/2", Center Hole 1/2", Width 2-1/2", Thickness .204. Commercial Mulcher Blade (3) blades for 60" cut.

Replaces O.E.M. #1-323515. Length - 16-1/4", Center Hole -5/8", Width - 2-1/2", Thickness - .204. (3) blades for 48" cut, 2 for 32". Fits Turf Tracer, HP Metro, & Viking.

Replaces O.E.M. #633569. Lazer Z. Pump Drive Belt- OEM spec belt

Replaces O.E.M. #1-643097 & 103-2521, Length 24-1/2", Center Hole 5/8", Width 3", Thickness .204 (3)blades for 72" cut. Mulching blade. Fits Lazer Z units.

Replaces O.E.M. #65301. Length 15-5/16", Center Hole 5/8", Width 2-1/2", Thickness .204. Commercial Mulcher Blade (3) blades for 44" cut.

Shock Damper replaces EXMARK 103-2913 EXMARK 103-4079 EXMARK 1-523027, EXMARK 109-2339 & TORO 103-4079 Fits Laser Z. 5/16" diameter hole tooth ends. 7" closed length, 11" entended length.

Replaces O.E.M. #103-1581, Length, 24-1/2", Center Hole 5/8", Width 3", Thickness .204 (3) blades for 72" cut. Solid Air Foil Hi-Lift.

Replaces Exmark 1-613098. Fits Floating Deck Walk Behinds. ID- 11/16", OD- 5-1/2", Height- 1-1/8".

Replaces Exmark #1-633701. Fits Lazer Z model numbers 150000 thru 259999. Fits our SH0353 spindle assembly.

Idler pulley replaces Exmark OEM# 1-413099.  ID-11/16", OD-5-3/4", HT- 2-1/2"

Idler pulley replaces Exmark 1-633109. Fits 52", 60", & 70" Deck belts on Lazer-Z units. ID-5/8", OD 6-3/4", Height-1-3/16".

Replaces O.E.M. #103-6395. Length 15-1/4", Center Hole 15/16", Width 2-1/2", Thickness .204. (3) blades for 44" cut. Mulching blade.

Replaces O.E.M. #103-6396. Length 16-1/4", Center Hole 15/16", Width 2-1/2", Thickness .204. (3) blades for 48" cut. Mulching blade.

Replaces Exmark OEM# 103-9630.  Commercial mulching blade. 3 blades used for 66" cut.  22-3/4" length, 15/16" center hole, 3" width, .204 thickness

Mulching blade replaces Exmark OEM# 103-6390. 3 blades used for 44" cut. 15-1/4" length, 2-1/2" width, 15/16" center hole, .204 thick.

Replaces O.E.M. #303080. 36" Engine to Blade Belt - OEM spec belt.

Replaces O.E.M. #403088.  48" & 52" Engine to Deck Belt - OEM spec belt.

Replaces O.E.M. #403018.  36" & 48" Engine to Transmission Belt.

Replaces O.E.M. #503016.  48" Engine to Transmission Belt.

Replaces O.E.M. #323017. 32" Engine to Deck Belt.

Replaces O.E.M. #403024.  48" Engine to Blade Belt.

Replaces O.E.M. #403025.  48" Blade to Blade Belt.

Replaces O.E.M. #323300. 48" Engine to blade belt

Replaces O.E.M. #303078.  Engine to Gear Box Belt.

Replaces O.E.M. #303080.  36" Engine to Blade Belt.

Idler pulley replaces Exmark OEM# 1-603843. Fits 32-48" Viking hydros. Heavy duty ID- 11/16" OD- 4-7/8" height- 3/4"

Replaces Exmark OEM#s 1-808502 & 1-32120-8.  Fits Lazer, Turf Ranger & Turf Tracer HP series 44", 48", 52", 60" & 72" decks.  2-1/4" OD, .066 thick.

Replaces Exmark #103-2477. Fits 60" and 72" Lazer Z XP. Bearing #RA100RR7. REF. NO.: CS203ASSY.     ID- 1.00", OD - 2.00", Height .711"

 

Replaces Exmark O.E.M.#103-0661 and 103-0662. Also replaces Warner #5218-76. Pulley 6-5/16", Height 3-3/8", Bore 1". Fits models Lazer Z below Serial No. 159,999. For 18 and 22 HP engines. Confirm O.E.M.# prior to ordering. 25% restocking fee on all returned Electric PTO Clutches.

Replaces Exmark O.E.M.#103-0690, 1-653048 and 1-653292. Also replaces Warner #5218-80. Pulley 7-3/8", Height 3-1/4", Bore 1". Fits models Lazer Z Serial No. 260,000 and higher. Confirm O.E.M.# prior to ordering. 25% restocking fee on all returned Electric PTO Clutches.

Replaces Exmark #303073. Spindle pulley. Fits 32", 36" and 48" cut mowers. 1"ID x 5-3/4"OD. 1/4" keyway. Two 5/16"-18 set screws.

Replaces Exmark #303072. Fits 32", 36" and 48" cut mowers. 5/8" ID x 3-1/2"OD. 3/16" keyway. 5/16"-18 set screws.

Replaces Exmark #602501. Heavy-duty style. 1/2"ID x 4-9/16"OD x 1-1/32" HT. Includes 3/8"ID reducer bushing.

Replaces Exmark #303381/303075. Heavy-duty style. Fits 32", 36" and 48" cut models. 1"ID x 5"OD. 1/4" keyway. Includes safety cap.

Replaces Exmark #1-513012. Includes locking collar and set screw. 1"ID, 2"OD, 1-3/4" Height.

Spindle Assembly replaces Exmark #1-634972. Fits Lazer Z model number 150000 thru 259999. Error in 2005 catalog listed as SH0533.

Spindle Assembly replaces Exmark #103-1184. Fits Lazer Z HP 52" decks.

Spindle Assembly replaces Exmark #103-3200. Fits Lazer Z HP 60" decks.

Replaces Exmark #603676. Bore Size 11/32", OD(Pin) 5/16", Shoulder Length 1/2". Total Length 1-7/32".

Exmark spindle housing with lip bearing replaces Exmark OEM#s 103-8280, 1-634619, 1-323532 & 103-2547.  Fits some Lazer, Front Runner, Metro, Phazer, Viking, Turf Tracer & Turf Ranger models.

1" ID, 5-1/4" OD, 3-3/4" HT

Replaces Exmark OEM# 103-2785 outer short shaft. 3/4"-16 Thread size, 7-1/2" Length, 1-3/4" OD Fits some Lazer Z & some Turf Ranger. Must be matching OEM# to know.

Replaces Exmark OEM# 103-0584.  7-1/4" length, 1-3/4" OD

Replaces Exmark OEM# 1-413330 & 413330. 7-3/16" length, 1-3/16" OD

Replaces Exmark shaft OEM# 103-0957. 7-1/4 length, 1-3/4" OD, Thread 5/8"-18.

Replaces Exmark 1-633696.  Fits Metro HP, Turf Tracer, Viking, Lazer & Turf Ranger models with OEM# 1-633696.  Conduit 54", Inner wire 56-1/4"

For Exmark Trition Mid Mount Deck. Jumbo, Heavy duty military spec. latch, Curved front directs grass to back of catcher for high density packing, Non vented front construction of catcher keeps grass from clogging mower outlet. Jumbo weighs 23# and holds 4.3 cubic feet. Tubular steel frame continuous weld superior to spot-weld catchers, 22 gauge solid and perforated sheet steel.

For deck belt adjustment replaces Exmark 303236.  **Limited Supply--discontinued item** 

Replaces Exmark #603602 Bushing, #98-5961 Bolt,#3290-357 Nut, #373034 Pivot Washer and #98-5975 Spring Washer. Kit consists of 1 each of the above items. Used with our WEX6917 Deck Wheel.

Front Seal Wheel Bearing replaces Exmark #633580. Fits Laser Z units. ID-1-1/8", OD-1-3/4", Width-7/16". PACKAGE of 5.

Spacer replaces Exmark #1-633579. Fits Exmark Laser Z 13x500x6 wheels. Used with our 506DC4-562SM wheel assembly. ID-1/2", OD-3/4", Length - 5- 7/8".

Replaces Exmark 513009 & 631560. ID-1/2", OD-1-3/8", Height-1/2".

Replaces Exmark 513809, 513810. Also replaces Encore # 363012. Roller cage bearing (1-1/4"ODx49/64"IDx3-23/32"length) and 2 retainer bushings.

Replaces Exmark 513547. ID-1/2", OD-3/4", Length-4-5/8".

Bolt replaces Exmark 800334. Nut replaces Exmark 80459. Fits 36", 48", 52", and 60" decks. For Turf Ranger, Turf Tracer, Viking and Metro models from 80000 series and higher. Thread size-1/2", Length-6".

Fits midsize 36", 48", 52", and 60" deck Turf Ranger, Turf Tracer, Viking and Metro models from 80000 series and higher. Includes open cage roller bearing, spanner, and retainer bushings. Overall ID-1/2", Overall OD-1-3/8", Overall Length-4-21/32". Includes OEM#s 513809, 513810 & 513547

Replaces Exmark 603602 & Toro 103-5364. Fits in deck wheel on Turf Ranger & Turf Tracer Explorer. ID-3/8", OD-5/8", Length-2-13/16", Flange OD-1". Used with our WEX6917 deck wheel.

Replaces O.E.M. #304173, 302017, Wheel size 13x650-6. Complete rear drive wheel assembly / 13x650-6 4-ply turfsaver tire mounted 1-piece rim with 7/8" open cage roller bearing, SINGLE pully, brake drum and zerk fitting. Painted white. For single wheel drive belt mowers.

Replaces O.E.M. #1-644251 & 103-0069. Wheel size 13x650x6, Caster wheel with bearings. 13x650x6, 4-ply smooth tread tubeless tire, 1-piece rim, 7" centered hub , 3/4" bearings with zerk fittings. Fits Lazer Z 52", 60" & 70" models. Uses our spanner WB9992.

Anti scalp roller deck wheel only.  Replaces Exmark OEM# 103-8415.  Fits Triton decks.  5/8" ID, 3-1/4" width, 5" HT. 

Replaces O.E.M. #603299. Wheel size 5x2.75, Deck wheel. 2-1/2" offset hub. ID 5/8", width 2-3/4", height 5". Plastic deck wheel for 38", 40", 50", & 60" cut decks. Uses our WB8586 wheel bushing OR our WB10007 complete anti-scalp roller hardware kit.

Wheel size 13x500-6, Replaces Exmark #634662 and Dixie Chopper # 67204.  13x500-6 flat free solid smooth tire on 1-piece white wheel, 5-5/8" center 3/4" bearing with zerk fitting. 

Universal adjustable yoke ends. 3/8" - 24 female, for 3/8" pin. Replaces Exmark #1-633131.

Replaces Exmark O.E.M.#103-0664, 1-631645 and 1-633099. Replaces Warner # 5218-5. Fits model Lazer Z part #103- 0664. Also replaces Bobcat #2188151, Ferris #1522040, Kees #102603. Pulley 6-5/16", Height 3-1/4", Bore 1-1/8", used 5/8" belt. Confirm O.E.M.# prior to ordering. 25% restocking fee on all returned Electric PTO Clutches.

6" Caster Yoke replaces Exmark #1-632511-01. Fits 13x5.00x6 wheel. Used on 52" Lazer Z HP (Painted Red).  Also replaces Toro # 632511

Wheel with gear replaces Exmark OEM# 100-2860 and Toro OEM# 74-1720. Fits Exmark Metro 21" and Toro 21" Recycler.  8-200 wheel size, 1-1/4" centered hub, 3/8" Bore. Diamond tread tire.

Replaces O.E.M. #483012. Walkbehinds - 48" Blade to Blade Belt.

Replaces O.E.M. #483013.  48" Engine to Blade Belt.

Replaces O.E.M. #483023.  48" Variable Speed Trani Belt.

Replaces O.E.M. #323030.  32" Blade Belt.

Replaces O.E.M. #363143.  36" Engine to Blade Belt.

Replaces O.E.M. #363245.  32", 36" - Variable Speed Trani Belt.

Replaces O.E.M. #362046, 362117, 976409, Wheel size 13x650-6, Complete rear drive wheel assembly on 48" commercial walkbehind / 13x650-6, 4-ply turfsaver tire mounted 1-piece rim with 7/8" open cage roller bearing, single pulley, brake drum and zerk fitting.

Replaces O.E.M. #362105, Wheel size 410/350-4. Front caster wheel on 48" commercial walkbehind 410/350-4, 2-ply sawtooth tire and tube mounted open cage roller bearing 3-piece centered wheel with zerk fitting, painted white.

Replacement Blade only for Felco F610.

This is a true left-handers version of the Felco 7, again, with all the same fine features as the Felco 7.

Suitable for every type of pruning. Ergonomic hand-fitting design. Superbly balanced the FELCO 11 offers a large cutting capacity. Narrow pointed anvil blade allows easy access to twiggy branches and assures a close cut to trunk. Precision alignment of cutting and anvil blade due to adjustable locking segment. Easy blade replacement. Shock absorbers reduce fatigue of wrist.

Quality Leather Belt Holster. Made in the U.S.A. Heavy duty quality grain leather. Waxed thread stitching and extra riveting for long lasting use.

This is the original Felco design, and has remained unchanged for over forty years. Imitated the world over, this popular model, like all other Felco models, continues the tradition of workmanship. Solid-forged metal alloy handles are complimented by a Swiss precision made hardened cutting blade (replaceable) and an anvil blade with a sap groove. A hardened bolt and nut assure exact adjustment of both the cutting and anvil blades. A rubber cushion and shock absorber provide smooth working and soft closing of this pruner.

Made of solid, forged light metal handles, cushion stops, sap groove on anvil blade and the famous Felco Fine blade adjustment. Because of its construction and great cutting performance Felco loppers have achieved top results when compared with other similar loppers on the market. Felco loppers cut up to 1-1/2" in diameter with ease. Length 17". Weight 27 oz.

FELCO loppers are made of solid, forged light metal handles, comfortable cushion stops and famous FELCO adjustment system. Screw mounted anvil blade has sap groove and slide resistant blocking grooves. Because of the construction and great cutting performance FELCO loppers have achieved top results when compared with other similar loppers on the market. FELCO 22 has cutting capacity up to 2 in. (50mm) in diameter. Length 33 in. (84mm) Weight 72 oz. (2035g).

Pruner Replacement Springs fits Felco 2, 4, 7, 8, 9. 10 & 11.  2 per pack.

An anvil pruning shear like no other. A design which is the result of intensive research and development of ANVIL technology. Cutting blade is beveled on both sides for easy clean-cut pruning. Handles are forged from robust aluminum alloy and are ergonomically shaped.

If you want more basic pruner without the refinements but still with the famous FELCO quality and cutting performance, the FELCO 4 is for you. This model offers the same quality cutting blade as the FELCO 2. The blade adjustment is by the center bolt and nut only. It has no rubber cushion, shock absorber or locking segment and it is priced accordingly.

This is the lowest priced FELCO pruner, still with excellent cutting ability. With handles from solid steel and simplified construction, it is an ideal choice for the home hobby gardener. No cushion stop, sap groove or wire-cutting notch.

Designed for those with smaller hands who may prefer a smaller, lighter pruner. It is comfortable to use yet every bit as sturdy and powerful as all the other FELCO models. Ideal for small pruning work such as grape vines, shrubs and young trees, it is also the choice of many florists. The anvil blade is screw-mounted. The shorter blades facilitate closer to the stem of the plant.

There is nothing ordinary about this patented blade. The shape of the blade is thinner at the top and thicker at the bottom-where the teeth are. This unique feature keeps only the teeth in contact with the material to be cut. This prevents clogging and binding, since the sides of the blade never come in contact with the wood. Cuts branches up to 4 inches (10mm) in diameter. Made in S. Korea for FELCO.

Replacement Blade for Felco 600.

Feature of blade design is the same as on the Felco 600 model. The blade cuts as smooth as if the wood was planed. The hand chrome plating prevents rust. Resins will not cling to the blade and green wood will not clog the teeth. For complete safety the saw cuts on the pull stroke. Cutting limbs up to 9 inches (23cm) is no problem. Supplied with removable safety sleeve. Made in Japan for Felco. Overall length 20in. (51cm), Blade length 12-1/2 in.(33cm), Weight 7.8oz. (220g).

Here is a superbly-designed pruning shear for the professional. The rotating handle revolves on its axis, allowing the fingers to move naturally, thereby reducing the blisters and hand fatigue that so often accompany prolonged pruning work. This unique swivel action requires up to thirty percent less effort than conventional models and offers maximum comfort on continuous-use jobs. Both the cutting and anvil blades are not riveted, and the narrow, pointed blade design allows for close pruning.

If you are undecided about the FELCO 7, we recommend this ergonomically designed pruner. It is identical to the FELCO 7, except for the rotating handle. Light alloy handles are shaped to act as an extension of the forearm. The anvil blade handle is designed to prevent the pruner from sliding through the hand. Hollow-ground, this Swiss precision, hardened steel blade features a wire-cutting notch. The blades are set on dowel for easy maintenance and replacement.

This is a true left-hander's version of the FELCO 8, with all the same features. LEFT-HANDED

An outstanding powerful tool for cutting up to 1/4" steel wire rope. Unique triangular jaws never leave a frayed cut. No landscape crew should be without this tool.

Innumberable are the uses for this tough, versatile little cutter. Cuts banding wire, tin, rubber, string, wire netting and all kinds of materials. No home or workshop should be without FELCO CP.

Replacement Cutting blade for Felco 2, 4 or 11.

Replacement Cutting bladefor Felco 7 or 8.

Replacement Cutting blade for Felco 9 or 10.

Replaces Ferris belt OEM# 22061 for 61" cut Zero Turn Rider Also fits Scag OEM# 482652 for Tiger Cub & Wildcat with 61" decks.

Replaces Ferris belt OEM# 20824 for 61" cut hydro walk behind

Replaces Ferris belt OEM# 21261 for 48" cut hydro walkbehind.

Replaces Ferris belt OEM# 21297 for 52" cut hydro walkbehind.  OEM spec belt.

Replaces Ferris belt OEM# 22148 for 52" cut zero turn rider.  OEM spec belt.

Replaces Ferris belt OEM# 22173 for 36, 48, 52, 61" cut walkbehinds.  OEM spec belt

Ferris transmission drive belt replaces OEM#s 5100555.  OEM spec. belt.  Also replaces OEM# 5022314

Replaces O.E.M. #1521227, Length 18", Center Hole 5/8", Width 2-1/2", Thickness .204 (2)blades for 36" cut, (3) blades for 52" cut.

Replaces O.E.M. #1520842, Length 21", Center Hole 5/8", Width 2-1/2", Thickness .240 (3)blades for 61" cut, Fits mid-mount ZTR

Replaces O.E.M. #1520843, Length 16-1/4", Center Hole 5/8", Width 2", Thickness .240 (3)blades for 48" cut, Low Lift Blade Sharpened 4-sides.

Ferris. Heavy duty military spec. latch, Curved front directs grass to back of catcher for high density packing, Non vented front construction of catcher keeps grass from clogging mower outlet, Weighs 19.5# and holds 3.3 cubic feet. Tubular steel frame continuous weld superior to spot-weld catchers, 22 gauge solid and perforated sheet steel.

Ferris Jumbo Catcher. Heavy duty military spec. latch, Curved front directs grass to back of catcher for high density packing, Non vented front construction of catcher keeps grass from clogging mower outlet. Jumbo weighs 23# and holds 4.3 cubic feet. Tubular steel frame continuous weld superior to spot-weld catchers, 22 gauge solid and perforated sheet steel.

Replaces O.E.M. #1520873. Hydro Walkbehind, 48" Deck Belt - OEM.

Replaces Ferris #1541478. Engine pulley. Fits 48" cut mower. 1"ID x 5-3/4"OD. 1/4" keyway.

In-line fuel filter replaces Kawasaki OEM# 49019-1055. **--not in our current catalog. This is an aftermarket version of our FF054059 original Kawasaki fuel filter. Limited stock available

Three pivoting nylon blades designed for cutting through thick weeds, Eliminates the task of line replacement no bolts required, Installs on any trimmer with brush blade attachments. Includes 4 nylon reducers for 3/8", 5/8", 3/4" and 20mm arbors. Recommended for use on trimmers smaller than 32cc.

Replaces Bunton PAL0368A and John Deere PT8649.  Also fits Snapper/Kees #76520. ID-3/8", OD- 3-1/32", Height- 7/8".

Replaces Gravely 34286 and Snapper 57582. ID- 3/8", OD- 4-1/2", Height- 2".

Pump Applicator, for use with 1-Gallon Bottle.

Reusable 5 gallon bucket Applicator (8 oz/stroke)

Flatguard is a complex non-latex based chemical formula containing a high concentration of special fibers and rubber particles suspended in a fluid base. After a puncture occurs the fibers surround and cling to the penetrating object preventing air loss and sealing the hole. 16 ounce bottle.

Flatguard is a complex non-latex based chemical formula containing a high concentration of special fibers and rubber particles suspended in a fluid base. After a puncture occurs the fibers surround and cling to the penetrating object preventing air loss and sealing the hole. 1 gallon bottle. FGTS74 pump applicator sold separetly.

Flatguard is a complex non-latex based chemical formula containing a high concentration of special fibers and rubber particles suspended in a fluid base. After a puncture occurs the fibers surround and cling to the penetrating object preventing air loss and sealing the hole. 5 gallon bucket.

Pair of 7/8" Foam Grips - Used on Bobcat, Exmark, Scag, Snapper and other midsize mowers.

Pair of 1" Foam Grips - Used on Bobcat, Exmark, Scag, Snapper and other midsize mowers.

Elbow cut-off with screen 1/8" pipe thread- 1/4" nipple. Replaces Lawn-Boy 677052 and Gravely 18563. Also fits older Snapper tanks.

1/4" in-line cut off valve. Replaces B&S 494768 & 698183.  Also fits Snapper 34212.

1/4" cut-off valve replaces B&S 399517 & 698182

Tecumseh 1/4" cut-off valve with filter.

Elbow cut-off valve. 1/8" pipe thread x 1/4" nipple. Replaces B&S 492030.

Economy Filter. Large in-line 2 step filter- 1/4"& 5/16" nipple. 60 micron interior element. Replaces Gravely 21410800, Onan 149-220601, Bobcat 38283/38666, Bunton PM244, Exmark 303197, Jacobsen 552265, John Deere AM116304, Kohler 2505003.

Replaces Kubota 15231-43560 and Woods 70666. 1/2" ID x 1-1/8 OD x 3-3/8" length.

Replaces Shindaiwa 22100-85420. Fits models T25, T27, C35.

Fuel Filter with weight replaces Shindaiwa 22100-85411. Fits models T25, T27, C35 & B45.

Fuel Pick-up Assembly replaces Stihl 1115-350-3503. fits models 045 and 056.

Replaces Walbro 125-527. Fits Engines up to 33cc. For 3/16" ID fuel line Felt filtered.

Fuel tank for mini-saws and most string trimmers with 1/8" pickup fuel line. Replaces Tecumseh 410263, 410245 and Homelite 49422, McCulloch 216985, Zama ZF-1

Replaces Walbro 125-528. Fits Engines up to 80CC. For 3/16" ID full line. Felt Filter.

Replaces Kawasaki 49019-2065. Fits trimmer models TD18, 22, 24, 33, 40 & 48.

Fuel Filter & Tube Assembly replaces Shindaiwa 20011-85401. Fits trimmer models T25, T27, C35 & B45.

Fuel line and filter assembly replaces Stihl 4112-350-3500. Fits model FS80.

Round in-line filter. Replaces B&S 394358 and Toro 566360 and Simplicity 173206. For 1/4" nipple. 75 Micron element. For engines with fuel pumps.

In-line filter for 1/4" nipple. Replaces Snapper 14359 and 11777, and John Deere AM107314. 85 Microns.

Large in-line two step filter 1/4" and 5/16" nipple. Premium filter-see thru plastic housing-paper interior element. Replaces Toro #715960. 9-15 microns. Used on many walkbehind mowers, riders & small tractors.

Round in-line filter for 1/4" fuel line. Replaces B&S 298090 and John Deere PT4265, Onan 149-2356, Scag 48057-02, Toro 42-5240. 150 micron element. For engines without fuel pump.

Aftermarket In-line fuel filter, replaces Kawasaki OEM# 49019-7001. Not in our 2008 catalog.   For original Kawasaki fuel filter, see our order # FF054071.

Replaces B&S 493629 and 691035. 60 micron filter for selected engines with fuel pumps.

Fuel filter replaces Kubota #12581-43012, Toro #18-1520, & Grasshopper #101005. Fits large horse power models. 10 micron. Fits 5/16" fuel line.

Replaces Kohler 2505002, Bobcat 38666, John Deere AM1008356, Woods 70311/70812. Fits 1/4" ID fuel line. Clear plastic, 80 micron includes 4 clamps.

****Limited Supply****

Replaces B&S 492836, Toro 18-1520 fits 5/16" ID full line. 10 micron. Universal metal style.

Replaces Kohler 2405002, Toro 83-1320 & 94-2690. Fits 1/4" ID fuel Line 10 micron. Fits Toro Greensmaster 3, 300, 3000, 3100 and Sand Pro. metal construction.

Replaces Stihl 1119-358-7700. For Stihl model 038.

3/32" ID x 3/16" x 10' Roll. Vinyl fuel and lubricant tubing. Special formula resists swelling or hardening. Translucent material allows visual inspection of flow.

1/8"ID x 1/4" OD x 10' roll. Vinyl fuel and lubricant tubing. Special formula resists swelling or hardening. Translucent material allows visual inspection of flow.

3/16" ID x 5/16" OD x 10' roll. Vinyl fuel and lubricant tubing. Special formula resists swelling or hardening. Translucent material allows visual inspection of flow.

1/4" ID x 3/8" OD x 10' Roll. Vinyl fuel and lubricant tubing. Special formula resists swelling or hardening. Translucent material allows visual inspection of flow.

Replaces Shindaiwa 20000-85303

Fuel tube replaces Shindaiwa 20011-85451. Fits models T25, T27, C35 & B45.

Gas Can Rack. Powder coated finish. Includes strap. Holds 1-5 gallon or 2-2.5 gallon rectangular polymer cans.

Keeps stored gas fresh indefinitely- no need to drain. For all 2-cycle and 4-cycle engines. Prevents rust and corrosion. Apply in fall for winter storage. Inexpensive- 4oz. treats 5 gallons of gas. Makes engines start easily, even after long term storage. Prevents stored fuel from oxidizing and forming gum and varnish. Specifically recommended by most engine manufacturers for use as a fuel stabilizer during winter storage. Prevents formulation of deposits that could clog filters and tiny passages in the fuel system. Helps protect gaskets from cracking, drying and shrinking.

Keeps stored gas fresh indefinitely- no need to drain. For all 2-cycle and 4-cycle engines. Prevents rust and corrosion. Apply in fall for winter storage. Inexpensive- 4oz. treats 5 gallons of gas. Makes engines start easily, even after long term storage. Prevents stored fuel from oxidizing and forming gum and varnish. Specifically recommended by most engine manufacturers for use as a fuel stabilizer during winter storage. Prevents formulation of deposits that could clog filters and tiny passages in the fuel system. Helps protect gaskets from cracking, drying and shrinking.

Keeps stored gas fresh indefinitely- no need to drain. For all 2-cycle and 4-cycle engines. Prevents rust and corrosion. Apply in fall for winter storage. Inexpensive- 4oz. treats 5 gallons of gas. Makes engines start easily, even after long term storage. Prevents stored fuel from oxidizing and forming gum and varnish. Specifically recommended by most engine manufacturers for use as a fuel stabilizer during winter storage. Prevents formulation of deposits that could clog filters and tiny passages in the fuel system. Helps protect gaskets from cracking, drying and shrinking.

Made in U.S.A. 12.5 to 1 gear ratio, Replaces Bobcat #38008-1N, Bunton #PAL0965, Jacobsen #552198, Exmark #302029, Snapper/Kees #76380 & #362025, John Deere PT8640. Manufactured by Dalton Gear.

Grass CatchHERR replacement latch.

Replacement Door, regular size (3.3 CU.FT.)

Replacement Door, jumbo size (4.3 CU.FT.)

Replacement Latch, fits regular size (3.3 CU.FT.) and jumbo size (4.3 CU. FT.)

Leaf Gobbler (adds 4.6 cu. Ft. to any 4.3 cut. ft Jumbo Gobbler only for total capacity of 8.9 cu. Ft).

·         Removes clogged grass from mower decks

·         Flexible curved tip conforms to the underside of the deck

·         Does not scratch the deck

·         Long, stainless-steel blade cuts through debris on the mower skirt

Includes a comfortable rubber over grip handle

The Scientifically Engineered Curvature Conforms to the Underside of Any Mower.

The Extra-Long Side Blade Cuts Away Built-up Debris on the Inside of the Mower Skirt.

This Special Design Means You Can Reach and Clean Places You Can’t with Any Other Tool.

The GRASSBUSTER (Patent Pending) is a Handy Tool that Cleans Even the Most Clogged Lawn Equipment in LESS THAN ONE MINUTE!

It is a High Quality Tool with a Durable, Spring- Tempered Blade Designed to Withstand Rigorous Use.

 

Replaces Grasshopper #48115

Replaces Grasshopper 393225. Fits models from 1984 thru 1994, 44", 48" and 52" decks (2 per deck). Composite: glass filled nylon. ID- 1/2", OD- 4-5/8", Height- 31/32"

Replaces Grasshopper 415650. Fits models 718, 720, 721, and 725. Cast iron 1/4" Keyway. ID- 1", OD- 5- 1/2", Height 1-29/32", Keyway- 1/4".

Replaces Grasshopper O.E.M. #604182, 388766, Toro #93-3160. Also replaces Warner #5215-62. Pulley 5", Height 3-3/4", Bore 1-1/8". Uses 1/2" belt. Confirm O.E.M.# prior to ordering. 25% restocking fee on all returned Electric PTO Clutches.

Replaces O.E.M. #320232, Length - 15", Center Hole - 1/2", Width - 2", Thickness .204. (3) blades for 44" cut. (High Lift) Also, 48" cut takes (1) GH15HL & (2) GH18HL blades.

Wheel size 9x350-4, 4-ply polyurethane smooth tire on 1-piece tan wheel with 5/8" ball bearing. Replaces OEM#s 603927, 603924, 483800.  Flat Free Tire.

Replaces Grasshopper 833260. Fits rider models 612, 616, 2144, 6144, 9044, 9148, 9052, 9061, 9244, 9252, 9261, 9372 and 9272. Oil impregnated.

Deck belt replaces Grasshopper OEM# 382082.  Fits M152 Deck. OEM spec belt

Mule Drive belt.  Replaces OEM# 382110.  Fits 322D diesel.  OEM spec belt.

Replaces O.E.M. #320236, 320237 and 320239. Length 18", Center Hole 1/2", Width 2-1/2", Thickness .204. Commercial Mulcher Blade (3) blades for 52" cut.

Replaces O.E.M. #320243, 320245 & 320242. Length 21", Center Hole 1/2", Width 2-1/2", Thickness .204. Commercial Mulcher Blade (3) blades for 61" cut.

Replaces O.E.M. #320231, Length 15", Center Hole 1/2", Width 2-1/2", Thickness .204. Commercial Mulcher Blade (3) blades for 44" cut.

Replaces Grasshopper 122044. Fits series 700. ID- 1", Length- 5-1/2", Height- 2-3/4".

Complete kit can be used for 9x350x4 front caster wheels. Includes (2) high speed bearings (5/8"IDx1-3/8"ODx7/16"thick). (1) spanner bushing (1/2"IDx5/8"ODx4-1/16" length), and (2) washers.

Replaces Grasshopper 120050 front wheel bearing. ID-5/8", OD-1-3/8", Height-1/2". Also replaces Dixie Chopper #10205.

Spanner bushing replaces Grasshopper 902473. Fits Grasshopper 603927, 9x350x4 caster wheel and Grasshopper 483861, 13x650x6 caster wheel. (21/32"ID, 7/8"OD, 2-3/8" length).

Replaces O.E.M. #603927, 603924, Wheel size 9x350x4, Caster wheel. Fits 44", 52", 61", and 72" cut. Models 2144, 6144, 6152 & 6161. 9x350x4, 4-ply smooth tubeless tire, 1-piece rim, 3-1/2" centered hub, 5/8" semi-sealed bearing with zerk fitting.

Replaces O.E.M. #603925, 483861, Wheel size 13x500-6, Tail wheel / 13x500-6, 4-ply rib tire, mounted 1-piece rim with 5/8" bearings, zerk fitting, painted tan, 3-3/4" centered rim. Fits 44", 52", 61", and 72" cut models. Rear wheel on ZTR mowers.

Replaces O.E.M. #483800, Wheel size 9x350x4, Deck wheel on 52" and 60" decks/ 9x350x4, 4-ply smooth tire mounted on 3-piece rim with zerk fittings 5/8" open-cage bearing, painted gold.

Replaces O.E.M. #320231, Length 15", Center Hole 1/2", Width 2", Thickness .204. (3) blades for 44" cut (Standard Lift). Also, takes (1) GH15 & (2) GH18 blades for 48" cut.

Replaces O.E.M. #320233, Length 15", Center Hole 1/2", Width 2-1/2", Thickness .240. Contour blade-fits 48" deck models 9548, 9548S, 9348, 9348S. 48" cut takes (1) GH15A & (2) GH18A.

Replaces O.E.M. #320236, Length 18", Center Hole 1/2", Width 2", Thickness .204. (3) blades for 52" cut (Standard Lift) Also, takes (2) GH18 and (1) GH15 for 48" cut.

Replaces O.E.M. #320238, Length 18", Center Hole 1/2", Width 2-1/2", Thickness .240. Contour blade. Fits 48" deck models 9548, 9548S, 9348, 9348S. 48" cut takes (2) GH18A & (1) GH15A.

Replaces O.E.M. #320237 & 320239. Length 18", Center Hole 1/2", Width 2", Thickness .204. (3) blades for 52" cut (High Lift). Also, 48" cut takes (2) GH18HL & (1) GH15HL blades.

Replaces O.E.M. #320242, Length 21", Center Hole 1/2", Width 2", Thickness .204. (3) blades for 61" cut (Standard Lift).

Replaces O.E.M. #320242, Length 21", Center Hole 1/2", Width 2-1/2", Thickness .240. Heavy Duty (3) blades for 61" cut (Regular Lift).

Replaces O.E.M. #320243 & 320245.  Length 21", Center Hole 1/2", Width 2", Thickness .204. (3) blades for 61" cut (High Lift).

Replaces O.E.M. #320243 and 320245.  Length 21", Center Hole 1/2", Width 2-1/2", Thickness .240. Heavy Duty (3) blades for 61" cut (High Lift).

Replaces O.E.M. #320242, Length 21", Center Hole 1/2", Width 2-1/2", Thickness .240. (3) blades for 61" cut. (Medium Lift)

Replaces O.E.M. #320250, Length 25", Center Hole 1/2", Width 2-1/2", Thickness .240. (3) blades for 72" cut. (Low Lift)

Replaces O.E.M. #320251 & 320253. Length 25", Center Hole 1/2", Width 2-1/2", Thickness .240. (3) blades for 72" cut. (High Lift)

Replaces O.E.M. #382627. 614 & 616 Transmission Belt - OEM spec belt.

Replaces Grasshopper OEM #382035. 61" Mid Mount Deck w/Diesel -OEM spec belt.

Replaces O.E.M. #382085. 61" Mule Drive Belt - Mid Mount Deck w/Diesel-OEM spec belt.

Replaces O.E.M. #382095. 61" Mule Drive Belt - Mid Mount Deck w/Diesel -OEM spec belt.

Replaces O.E.M. #381914. PTO-1822 Diesel - OEM spec belt.

Replaces O.E.M. #382025. 61" - Deck Drive Belt - Short Belt.  OEM spec belt.

Replaces O.E.M. #382049. 61" - 6061 & 6261 Long Blade Belt - OEM spec belt.

Replaces O.E.M. #382025. 61" - Deck Drive Belt - Short Belt.

Replaces O.E.M. #381100. PTO-1210 - Tractor Unit Rear Engine.

Replaces O.E.M. #382000. PTO-1620, 1820, 1822 Gas-Rear Engine.

Replaces O.E.M. #382037. 52" - 6052 & 6152 Long Blade Cog Belt - OEM spec belt.

Replaces O.E.M. #382049. 61" - 6061 & 6261 Long Blade Belt.

Replaces O.E.M. #382570. 61" - 6061 Deck Drive Belt.

Replaces O.E.M. #382730. 744-Vac Belt.

Replaces O.E.M. #382740. 44" - Grass Vac. *This item is not in our current catalog*

Replaces O.E.M. #382750. 752- Vac Belt. *This item is not in our current catalog*

Replaces O.E.M. #382753. 52" - Grass Vac.

Replaces O.E.M. #382765. 61" - Grass Vac.

Replaces O.E.M. #383000. 2044, 6044 - Blade Belt.

Replaces O.E.M. #382777. 48" - Deck Drive Belt - Short Belt.  OEM spec belt.

Replaces O.E.M. #382800. 52" - Deck Drive Belt - OEM spec belt.

Replaces O.E.M. #382836. 48" - Deck Drive Belt - Long Belt.  OEM spec belt.

Replaces Grasshopper O.E.M. #388762, 604180, Woods #70903, 73113. Also replaces Warner #5218-27. Pulley 4-7/8", Height 3-13/16", Bore 1". Uses 1/2" belt. Confirm O.E.M.# prior to ordering. 25% restocking fee on all returned Electric PTO Clutches.

Replaces Grasshopper O.E.M. #388767, 606242, Woods #73558, Snapper 3-5520/5-8925. Also replaces Warner #5218-58 & 5218-26. Pulley 4-7/8", Height 3-3/8", Bore 1-1/8". Uses 1/2" belt. Double pulley. Confirm O.E.M.# prior to ordering. 25% restocking fee on all returned Electric PTO Clutches.

Replaces Gravely 22063. ID- 1/2", OD- 6-3/4", Height- 3/4".

Replaces Gravely O.E.M. #09232700, 09266700, Great Dane #GDA10122. Also replaces Warner #5218-31 & 5218-94. Pulley 6", Height 3-7/8", Bore 1-1/8". Uses 1/2" or 5/8" belt. Confirm O.E.M.# prior to ordering. 25% restocking fee on all returned Electric PTO Clutches.

Wheel size 280/250-4, polyurethane sawtooth tire on 3-piece white wheel with 3/4" open cage roller bearing. Flat free tire.

Replaces Gravely #45205. 9x350-4 flat free smooth tire on 3-piece white wheel with 3/4" open cage roller bearing.

Replaces Gravely 18355. Yoke Bushing on Promaster, Pro40, Pro50, Pro100 and Pro200. Nylon. ID-1", OD-1-3/8", Height-3/4", Flange OD-1-3/4".

Replaces O.E.M. #4916400. Also replaces Ariens #04916400, and Exmark 1-303527. Length 18", Center Hole 5/8", Width 2-1/2", Thickness .204. (3) blades for 52" cut.

Replaces O.E.M. #14668, 34984, 03498451, 08899800, Length 13-7/8", Center Hole 5/8", Width 2", Thickness .204. (3) blades for 40" cut.

Replaces O.E.M. #11234, 88616, 8861651, 08899300, Length 17", Center Hole 5/8", Width 2", Thickness .204. (3) blades for 50" cut.

Replaces O.E.M. #38947, 206562. Length 17", Center Hole 5/8", Width 2", Thickness .240. Low lift blade. Sharpened 4 sides (3) blades for 50" cut.

Replaces O.E.M. #046998, 87792, 8779251, 08899600, Length 17", Center Hole 5/8", Width 2-1/2", Thickness .240. (3) blades for 50" cut. (High Lift)

Replaces O.E.M. #212850, 21285051. Length 17", Center Hole 5/8", Width 2-1/2", Thickness .240. (3) blades for 50" cut. ZTR

Replaces O.E.M. #52928, 8866851, 08899200, Length 17", Center Hole 5/8", Width 2-1/2", Thickness .240. (3) blades for 50" cut. Fits Pro 50 & Promaster 50. Mulching blades

Replaces O.E.M. #42124, 88166, 08899400, Length 17-11/16", Center Hole 5/8", Width 2", Thickness .240. (2) blades for 36" cut. (High Lift)

Replaces O.E.M. #52927, 8866751. Length 17-11/16", Center Hole 5/8", Width 2-1/2", Thickness .240. (2) blades for 36" cut. Fits Pro 36 mower Mulching blade

Replaces O.E.M. #25124, 89046, 8904651, 0889900, Length 20-1/2", Center Hole 5/8", Width 2", Thickness .240. (2) blades for 40" cut. (3) blades for 60" cut.

Replaces O.E.M. #9212P2, 200347, 20034751, 009212, Length 20-1/2", Center Hole 1", Width 2-1/4", Thickness .250. (2) blades for 40" cut. Commercial Deck

Replaces O.E.M. #52929, 08899100, Length 20-1/2", Center Hole 5/8", Width 2-1/2", Thickness .240. (3) blades for 60" cut. Fits ProMaster 300 & Pro 40 Mulching blade.

Replaces O.E.M. #38946, 46999, 20656151. Length 20-1/2", Center Hole 5/8", Width 2", Thickness .240. (2) blades for 40" cut. (3) blades for 60" cut. Sharpened 4 sides.

Replaces O.E.M. #89796, 046999, 8979651. Length 20-1/2", Center Hole 5/8", Width 2-1/2", Thickness .240. (3) blades for 60" cut.

Replaces O.E.M. #48864, 8781851. Length 20-1/2", Center Hole 5/8", Width 2-1/2", Thickness .240. (3) blades for 60" cut. Mulching blade. Fits 60" mower with fabricated deck.

Replaces O.E.M. #047685, 89838, 8983851, 08898800, Length 24-1/2", Center Hole 5/8", Width 2-1/2", Thickness .240. (3) blades for 72" cut.

Replaces O.E.M. #12722. Gravely oil filter for L series tractors.

Replaces O.E.M. #34346/41599. 36", 40", 50" - Wheel Drive - Cogged - OEM spec belt.

Replaces O.E.M. #38745. 36" - Blade Drive Belt - OEM spec belt.

Replaces O.E.M. #72266/51213/11216. Pro 50" Cutter Deck Belt - Cogged.  OEM spec. belt.

Replaces O.E.M. #72258 and 7225800. Set of 2. Pro 150 - Wheel Drive - OEM spec belt.

Replaces O.E.M. #72224/49029. Set of 2. Pro Series - Wheel Drive Belt - OEM spec belt.

Replaces O.E.M. #72231/51141. Pro 100, 200, 300 - Drive Belt - OEM spec belt.

Replaces O.E.M. #72250. Pro 100, 200, 300 - PTO Belt - OEM spec belt.

Replaces O.E.M. #52776/72238. Pro Series - 36, 38, 40, & 50 - Trani Belt - OEM spec belt.

Replaces O.E.M. #43195. Engine to Transmission Belt.

Replaces O.E.M. #43213. PTO Clutch Belt.

Replaces O.E.M. #34289. 50" - Engine to Deck Belt.

Replaces O.E.M. #34332. 40" & 50" Transmission Belt.

Replaces O.E.M. #41545. Pro Series - Engine to Transmission Belt.

Replaces O.E.M. #34864. PTO Clutch Belt.

Replaces O.E.M. #34944. Pro 50 Blade to Blade Belt.

Replaces O.E.M. #34945. Pro 40 Engine to Blade Belt.

Gravely Pro (40" deck), Heavy duty military spec. latch, Curved front directs grass to back of catcher for high density packing, Non vented front construction of catcher keeps grass from clogging mower outlet, Weights 19.5# and holds 3.3 cubic feet. Tubular steel frame continuous weld superior to spot-weld catchers, 22 gauge solid and perforated sheet steel.

Gravely Pro (40" deck), Heavy duty military spec. latch, Curved front directs grass to back of catcher for high density packing, Non vented front construction of catcher keeps grass from clogging mower outlet. Jumbo weighs 23# and holds 4.3 cubic feet. Tubular steel frame continuous weld superior to spot-weld catchers, 22 gauge solid and perforated sheet steel.

Gravely Pro 32" & 36" fabricated deck & 50" stamped deck. Heavy duty military spec. latch, Curved front directs grass to back of catcher for high density packing, Non vented front construction of catcher keeps grass from clogging mower outlet. Jumbo weighs 23# and holds 4.3 cubic feet. Tubular steel frame continuous weld superior to spot-weld catchers, 22 gauge solid and perforated sheet steel.

Roller cage bearing with retainer bushings for Gravely 9x350x4 front caster wheel. Bearing (3/4"IDx1-1/4"ODx2-1/2" length) and retainer bushings (3/4"IDx1-1/2"ODx3/8" height). Uses our WB8420 spanner bushing.

Replaces Gravely 11387. Fits 40" center mount mower models. (1/2"ID, 3/4"OD, 2-5/8" length).

Spanner bushing replaces Gravely 92061. Fits ProMaster 200 caster wheel 50" & 60" cut models. (17/32"ID, 3/4"OD, 6-1/4" length).

Spanner bushing replaces Gravely 91052. Fits ProMaster 100 caster wheel 40" & 50" cut models. (17/32"ID, 3/4"OD, 5-3/32" length). ***limited supply***

Replaces O.E.M. #045205, 52586, Wheel size 9x350-4, New style caster wheel used Promaster 36", 40", 50", and 60" decks / 9x350-4, 4-ply smooth tire and tube mounted 3/4" open cage roller bearing centered 3-piece wheel with zerk fitting, painted white.

Replaces O.E.M. #92537, Wheel size 5"x2.75", Deck Wheel. 3-5/16" centered hub. 1/2" ID, 2-3/4" width, 5" height.

Replaces O.E.M. #034347, 042270, Wheel size 13x650-6, Complete rear drive wheel assembly (1986 and prior) 13x650-6, 4-ply turfsaver tire, mounted 1-piece rim with 7/8" open cage roller bearing, single pulley, brake drum and zerk fitting, painted white. For single wheel drive belts.

Replaces O.E.M. # 011386, Wheel size 6x2.00, Caster wheel used on 40" and 50" commercial mowers / 6x2.00-3/4" bushing centered wheel with zerk fitting and solid tire, 2-1/2" centered hub.

Gravely Pro G & Pro H (2002 and later) Heavy duty military spec. latch, Curved front directs grass to back of catcher for high density packing, Non vented front construction of catcher keeps grass from clogging mower outlet. Jumbo weighs 23# and holds 4.3 cubic feet. Tubular steel frame continuous weld superior to spot-weld catchers, 22 gauge solid and perforated sheet steel.

14 oz. tube multi-purpose grease. Used in our GG61 grease gun.

130 piece assortment. Includes straight, 45 degree elbow, & 90 degree elbow fittings in 1/4"-28 & 1/8" pipe sizes.

Lever action grease gun. Uses 14 oz. grease cartridge or can be bulk loaded.

Idler pulley replaces Great Dane D18031. Fits Surfer, Chariot, & Scamper models. Also replaces Scag 482217. ID-3/8", OD 5", Height-7/8".

Replaces Great Dane D18314. ID- 3/8", OD- 4", HT- 1-3/8"

Replaces Great Dane D18044. Drive Pulley with welded 12 point hub used with our SH9754 spindle assembly. ID- 1", OD- 5-3/4", Height- 3/4".

Wheel size 13x500x6, 4-ply smooth tire on 3 piece yellow rim, 3/4" high speed bearings, 5-5/8" centered hub, spacer between inner races.

Wheel size 13x650x6, 4-ply smooth tire on 3 piece yellow rim, 3/4" high speed bearings, 5-5/8" centered hub, spacer between inner blades.

Replaces Great Dane OEM# D18004 for 48", 52" & 61" Surfer.  OEM spec belt.

Replaces Great Dane OEM# D18006 belt for 52" Surfer.  OEM spec belt.

Replaces #D48003, 2-1/4" I.D. x 6" O.D. x 1-1/2" HT.

Replaces O.E.M. #D18087. 48" Surfer Blade Drive Belt - OEM spec belt.

Replaces O.E.M. #D18005. 52" Surfer Blade Drive Belt - OEM spec belt.

Replaces O.E.M. #D18007. 61" Surfer Blade Drive Belt - OEM spec belt.

Replaces O.E.M. #D28028. 61" Chariot Blade to Blade Belt - OEM spec belt.

Replaces O.E.M. #D28029. Chariot Blade Drive Belt - OEM spec belt.

Replaces O.E.M. #D28030. Chariot Hydro Pump Drive Belt - OEM spec belt.

Replaces O.E.M. #D28031. 52" Chariot Blade to Blade Belt - OEM spec belt.

Replaces O.E.M. #D18303. Super Surfer Engine Pump Belt - OEM spec belt.

Replaces O.E.M. #D18348. 48" Super Surfer Engine Blade Belt - OEM spec belt.

Spindle pulley replaces Great Dane D18084. Long HUB. ID-7/8"splined, OD 5-3/4", Height-1-1/8".

Drive pulley replaces Great Dane D18083. Short HUB. ID-7/8" splined, OD 5-3/4", Height-3/4".

Blade drive Idler pulley replaces Great Dane D28105. Fits Chariot models. ID-3/8", OD 5-7/8", Height-3-1/8".

Replaces O.E.M. #D18086. Length 16-1/2", Center Hole 5/8", Width 2-1/2", Thickness .204. (3) blades for 48" cut.

Replaces O.E.M. #D18037. Length 18", Center Hole 5/8", Width 2-1/2", Thickness .204. (3) blades for 52" cut.

Replaces O.E.M. #C39949. Length 21", Center Hole 5/8", Width 2-1/2", Thickness .204. (3) Blades for 61" cut.

Great Dane (48" & 52") (special order) Heavy duty military spec. latch, Curved front directs grass to back of catcher for high density packing, Non vented front construction of catcher keeps grass from clogging mower outlet. Jumbo weighs 23# and holds 4.3 cubic feet. Tubular steel frame continuous weld superior to spot-weld catchers, 22 gauge solid and perforated sheet steel.

Spindle assemby replaces Great Dane 200262.  New heavy duty style with mounting studs.

Replaces O.E.M. #305901. Fits model 2500 LP. Length or O.D. - 2-1/4", Width or I.D. - 2-3/8", Thickness or HT. - 1/2".

Replaces O.E.M. #309891. Green machine - fits model 3000 SS, Shindaiwa models T25 & LT20 20000-81740. Also fits Robin 1082. Length - 2-3/8", Thickness or HT. - 1/2".

Starter rewind spring replaces OEM#300285. Fits model numbers 3000, 3100, 2000, 2500, (...201446).

Replaces O.E.M. 357102, 2510LP, 3000SS (after S#7122429), 3510 (after S#700001)

*Limited supply*

Walbro carburetor fits Green Machine model #3000LP trimmers and Zenoah G560, G560AVS trimmers. Walbro WY-4.

Grey, Diameter 8", Thickness 1", Center Hole 5/8".

Grey, Diameter 7", Thickness 3/4", Center Hole 5/8".

For a safer cleaner shop add a grit collector to your grinder. The grit collector provides a simple method of containing flying sparks & grit. Easy to attach & can be reversed for left or right hand sharpening. For RBG1012C Grinder.

For a safer cleaner shop add a grit collector to your grinder. The grit collector provides a simple method of containing flying sparks & grit. Easy to attach & can be reversed for left or right hand sharpening. For BG121 Grinder.

For a safer cleaner shop add a grit collector to your grinder. The grit collector provides a simple method of containing flying sparks & grit. Easy to attach & can be reversed for left or right hand sharpening. For RBG 3410C Grinder.

141 Piece Hair Pin Cotter Assortment. From 1/16"x1-3/8" up to 3/16"x3-1/4" sizes.

480/400x8, HiSpeed, sawthooth, 4 ply tubeless tire

570x500-8, HiSpeed ,sawthooth 4 ply tubeless tire

16.5x6.5x8, HiSpeed - load range C - 6 ply tubeless.  **Limited Supply-discontinued item**  

480-12, HiSpeed, sawtooth, 4 ply tubeless tire

530-12, HiSpeed ,sawtooth, 4 ply tubeless tire

18.5x8.5x8, HiSpeed - load range C - 6 ply tubeless Metric size 215/60-8 **LIMITED SUPPLY AVAILABLE--discontinued item**

20.5x10, HiSpeed - load range C - 6 ply tubeless ** LIMITED SUPPLY only 1 AVAILABLE--Discontinued item**

F78-15, HiSpeed - load range C - 6 ply tubeless

Premium Red High Temp Grease for spindle assemblies, etc. 14oz tube.

Starter rewind spring replaces OEM#207575. Fits model numbers GT14B, 14T, WT14H, FT215T, 215B, JP215, WT215HB.

Starter rewind spring replaces OEM#206073. Fits model numbers 215B, JP215, WT215HB, PC225, GT225, GT320, B, T, H, JP420.

Foam Prewrap for our part H0702 & KO11505

Replaces Kubota O.E.M. # 15853-32430 & 15853-99179. Also replaces Honda #15410-MCJ-003. Fits model GXV530 16 HP V-Twin engine.

Replaces O.E.M. 17210-ZE6-505, 17210-ZE6-003 Code 1495902. Fits 3.5, 4, and 5 HP models GXV120, GXV140, GXV150, GV200. HR194. HR195. Replaces old No. 17211-888-013 & old code 1007483. Complete with foam wrap. OD- 7-1/2", ID- 2-1/2", Height 1-5/8".

Replaces O.E.M. 17210-ZE3-010 & 17210-ZE3-505,Code 2893907. Fits 8 thru 13 HP models GX240, GX270, GX340, GX390. Complete with foam wrap. OD- 4-3/8", ID- 3-1/16", Height 3-5/8".

Replaces O.E.M. 17210-ZE7-013 Code 2741627. Also replaces 17210-ZE7-505 & 17210-ZE7-003. Fits 4 & 5 HP vert. engines GVX120, GVX140 GXV160 Commercial mower models HR216 & HRA216, Complete with foam wrap. OD- 7-1/2, ID- 2-1/2", Height- 1-7/8".

Replaces O.E.M. 17210-ZE8-003, 17210-ZE8-013 &17210-ZF5-505. Code 2090207. Honda- 8-1/2 thru 13 HP OHV engines GXV270, GXV340, GXV390. Comes complete with foam wrap. OD- 5", ID 2-5/8", Height- 3-1/8".

Replaces O.E.M. 17211-ZA0-702 & 17210-ZA0-506. Code 2893923. Fits HT3813 & 4213 tractors. Also fits GX360K1 vertical engines. Complete with foam wrap. OD- 6-1/2", ID- 4-1/8", Height- 1-5/8".

Replaces O.E.M. 17210ZE6003 Code 149590-2. Honda air filter- 3-1/2 to 5 HP engines complete with foam prewrap. OD 7-1/2", ID 2-1/2", Height- 2". **LIMITED SUPPLY**

Replaces O.E.M. 17211-ZG9-M00. Fits SX series. Harmony 215 model HRM215.  OD- 5-3/4", ID- 3-1/2", Height- 1".

Replaces O.E.M. 17210-ZEO-822 Code #2893873. Fits GX 110 (old 3-1/2HP) & GX120 (new 4HP engine). Also fits Tiller model #400, 401K1 Horiz. Shaft. Complete with foam wrap. OD- 4", ID- 2-7/8", Height- 2-1/8".

Replaces O.E.M. 172A1883902 Code 2893915. Fits model G200 Engines. Complete with prefilter. Top- 3-1/8", Bottom- 4-3/8", Height- 2-3/8".

Air filter replaces Honda 17211-ZL8-000 , 17211-ZL8-003 & 17211-ZL8-023. code 5580402. fits unit GC 135, GCV 135 & GC 160, GCV 160. ID - 4-1/2", OD - 5-1/4", Height -3/4".

Replaces O.E.M. 17210-ZE2-822, 17210-ZE2-505, 17210-ZE2-821, 17210-ZE2-521 and 17210-ZE2-515. Code 2538429, 5266721 & 7460976. Honda 8 & 9 HP horiz. models GX240 & GX270. Complete with foam wrap OD- 4", ID- 3-1/2", Height- 3-1/8".

Replaces O.E.M. 17211890023 Code 102518. Honda 11HP horz. Models G300, G400- Fits model 3810 tractor-also fits 7&10 HP engines. Complete with foam wrap. Top- 3-7/8" Bottom- 5-1/4", Height- 2-5/8".

Replaces O.E.M. 17210ZE1821 & 17210ZE1505,17210ZE1820, 17210ZE1822 Code 2893881,5247408, and 144572. Honda 3.5, 5, 5.5 HP horz. Model GX110, GX120, GX140, GX160. Complete with foam wrap. OD- 4", ID- 2-7/8", Height- 2-5/8".

Replaces Honda #31210-ZE3-013. Fits model GX340. Solenoid not included. Special order item. 30% restocking fee if returned. Match OEM # before ordering.

Replaces Honda #17620-ZL8-003, code 5580451. Fits GC V130/160 and GC 130/160.

Fuel cap replaces Honda 17620-ZH2-W00 & 17620-ZH7-023. Fits 4-8 HP engines. Metal cap.

Replaces Honda #17620-ZH7-013, code 3682028. Fits 4-8 HP engines. Plastic cap.

Replaces O.E.M. 17218-888-003 Code 1067149. Extra foam prewrap for H0003.

Replaces O.E.M. 17218-ZE3-000 & 17218-ZE3-505. Code 2577377. Extra foam prewrap for H0010.

Replaces O.E.M. 17218888003. Extra foam prewrap for H0013.

Replaces O.E.M.# 15400-679-023 & 15410-MJ0-004,Code #1384445 and Kubota 30401-37580. Fits model GX360K1 (water cooled) engines, tractor models 3813 & 4514. Also fits models F22100 & F22400. 25/30 micron.

Extra Foam prewrap for part H008.

Replaces Honda #31200-HM8-003. Used on models 1997-2000, TRX. 12 volt ccw. Special order. 30% restocking fee if returned. Match OEM # before ordering.

Replaces Honda #31200-HC4-023, 31200-HC4-033. Used on models 1987,ATC250ES, ATC250SX, 1988-2000 TRX300, TRX300FW. 12 volt ccw. Special order. 30% restocking fee if returned. Match OEM # before ordering.

Replaces Honda #31200-ZJ1-004/31200-ZJ4-003. Fits GX610 and 620, GXV610 and 620. 12 volt ccw, 10 tooth. Special order. 30% restocking fee if returned. Match OEM # before ordering.

Replaces O.E.M. #72511-VE1-001, Code 4513511. Also replaces OEM# 72511-VE1-020.  Length 20-5/16", Center Hole .804, Outside Hole 13/32", Width 2-1/4", Thickness .134. Fits 21" Walkbehind models HRB215, HRM215. (High Lift)

Replaces O.E.M. #72531-VE2-001, Code 4513529. Length 21", Center Hole 1-17/64", Outside Hole 13/32", Width 2-5/8", Thickness .095. Upper blade. Use with our HO6431 lower blade. Fits 21" Walkbehind.  Also replaces Honda OEM#s 72531-VE2-020 & 72531-ZE2-010.

Replaces O.E.M. #72511-VE2-000, Code 4010609. Length 20-7/8", Center Hole .830, Outside Hole 13/32", Width 2-1/4", Thickness .095. Lower blade. Use with HO6430 upper blade. Fits 21" Walkbehind

Replaces O.E.M. 17218888003 Code 1067149. Extra foam prewrap for part H087.

Replaces Honda# 17210-ZJ1-841 Fits models 610K1, 620K1, 670, GXV610K1 and GXV620K1. 9" length, 6-1/2" width, 1-1/4" height.

Pre filter replaces Honda 17218-ZJ1-840. Fits models 610K1,620K2, 670, GXV610K1, GXV620K1. Pre filter for our HO10678 air filter.

Replaces Honda# 17010-ZJ1-000 Fits models GX610, 620, GXV610 and GXV620. 9-1/2" length, 8" width, 1-1/4" height.

Replaces Honda# 17210-759-013. Fits models GX610, and 620, with remote type air cleaner assembly. 9" length, 6-1/2" width, 1-1/4" height.

Replaces Honda# 17211-Z0A-013. Fits models GCV530 and GXV530, 16 HP V-twin vertical shaft units, 8-5/8" length, 4-3/4" width, 7/8" height.

Prefilter for our HO10879 air filter.

Replaces O.E.M. #72531-752-J00. Length 15-11/16", Center Hole .630, Width 2-3/4", Thickness .187. (3) blades for 46" cut. Fits models H-4518, H-5013 & HRT-5000.

Replaces O.E.M. #72531-758-L00. Length 19-1/2", Center Hole .630, Width 2-3/4", Thickness .187. Fits 38" deck models 4514, 4518, 3013 & 4013. Takes (1) HO19A & (1) HO19B. Left hand blade.

Replaces O.E.M. #72511-758-L00, 72511-771-l00. Length 19-1/2", Center Hole .630, Width 2-3/4", Thickness .187. Fits models 4514, 4518, 3013 & 4013. Takes (1) HO19B & (1) HO19A. Right hand blade.

Replaces O.E.M. #72511-960-004, Code#2801595, 72511-VA2-690. Length 20-7/8", Center Hole .845, Outside Hole .415, Width 2-1/4", Thickness .150. Fits HR214, HRA214, HRA216.

Replaces O.E.M. #72511-VA4-641, Code #3504230. Length 20-7/8", Center Hole .845, Outside Hole .415, Width 2-1/4", Thickness .150. Fits all Honda 21" cut from 1981-1991. 21" Mulcher.

Starter rewind spring replaces OEM#28442-896-700. Fits model numbers HRC 216, HR17 PDAM.(093310).

Starter rewind spring replaces OEM#28442-883-000. Fits model numbers HR21, PDAM, HR21, SXAM, HR21-5, SDAM, HRA21, SDA, HRA21, SDAW, F500A1,F500A2, FR500, FR700, EM-1600-3000, WA20, HS35-550, SDAM/AW.

Starter rewind spring replaces OEM#28442-896-000 (092972). Fits model number F200.

Replaces OEM# 28447-878-810 (044186). Fits Model Number Honda F400AZ.

Replaces O.E.M. #72513-751-020, Code# 2160372 & 2385508, 72513-751-003, Length 29-3/4", Center Hole 1.02, Outside Hole .480, Width 2-3/4", Thickness .160. Fits mid-engine rider model HTR3009.

Lower blade replaces Honda OEM# 72511-VK6-000, 7869381.  fits HRC216 K2 HXA.

Length- 21-1/4", Centerhole- .807, Width- 3-1/2", Thickness- .098

Upper blade replaces Honda OEM# 72531-VK6-010, 7869555, code 8504896.  Fits HRC216 K2 HXA.

Length-20-7/8", Centerhole- 1.25", Width 2-5/8", Thickness- .118

Replaces O.E.M.# 08750-960-333. Length 20-7/8", Center Hole .845, Width 2-1/4", Thickness .160. Off set blade. Fits 21" cut models.

Extra foam Prefilter for part H07980.

Replaces O.E.M. 17218-ZEO-821 Code #2535011. Extra foam prewrap for H0822.

Replaces O.E.M. #17211-ZG9-800. Fits models GVX 140, 5 HP vertical shaft. Waffle panel construction. Length or O.D. - 5-1/4", Width or I.D. - 2-1/4", Thickness or HT. - 1". Comes with pre-filter

Extra foam prewrap for H08903F. Replaces OEM# 17218-ZG9-800, code 4327391

Replaces O.E.M. #17211-896-000. Fits models G100, 2 & 2.5 HP engines. Used on McLane & Powertrim edgers, also on Honda pumps. Length or O.D. - 3", Width or I.D. - 3-1/2", Thickness or HT. - 1/2".

Replaces O.E.M. #17211-ZE7-W03, code 5357389. Pre-filter included. Fits 5.5 HP vertical shaft engine. Length  - 6-3/4", Width - 2-1/4", Height - 2".

Extra foam prewrap for H08906.

Replaces O.E.M. 17218-883-901 Code #1067131. Extra foam prewrap for H0902.

Replaces O.E.M. 17218ZE2821 Code 2338249. Extra foam prewrap for part HOS18.

Replaces O.E.M. 17221-899-003. Extra foam prewrap for part HOS23.

Replaces O.E.M. 17218-ZE1-821. Code 2535029. Extra foam prewrap for part H0S84.

Replaces Honda #18310-ZE2-013. Fits GX240 and GX270 with 2 piece muffler shield. Shield not included.

Replaces Honda #18310-ZE2-W00. Fits GX240 and GX270 with 1 piece muffler shield. Shield not included.

Handle knob replaces Honda OEM# 53125-VA4-K10, code 3338076.  Fits walkbehind mowers.  8mm 5-star.

Muffler replaces Honda 18310-ZF1-000. Fits 5.5 HP engines. Model GX160. Heat Shield included.

Replaces Honda #17672-880-000. Honda code #0474759. Fits models GX110, GX120, GX160, GX200, GX240, GX270, GX340 and GX390.

Replaces Honda #17510-ZE1-020ZA. Honda code #3683661. Fits models GX140, GX160 and GX200.

Replaces Honda 17510-ZE2-010ZA. Honda code #3690070. Fits models GX240 and GX270.

Replaces Honda #17510-ZE3-010ZA. Honda code #3713278. Fits models GX340 and GX390.

Replaces Honda 28400-ZE1-003ZA, Code 3373768. Fits Honda series GX110, 120, 140, & 160.

Starter rewind spring replaces Honda 28442-ZE6-003. Fits Honda model GX100QE. Multi fit starter.

Starter rewind spring replaces Honda 28442-ZE1-003. Fits Honda model GX110, GX140, GX160 multi fit starter. Single ratchet (before 1995).

Starter rewind spring replaces Honda 28442-ZH8-003. Fits Honda model GX120, GX160, multi fit starter. Twin ratchet (after 1995).

Starter rewind spring replaces Honda 28442-ZE1-713. Fits Honda model GX240, GX340, multi fit starter. Single ratchet (before 1995).

Replaces Honda 17910-VA3-003. Fits models HR194, HR215 and HR216. Conduit 42-1/2" Inner Wire 46" Wire Travel 2-3/4"

Replaces Honda 54530-VA3-J03. Fits models HR215SXA, HXA, K1SXA, K1HXA, HRC215, K1SDKA, HRC216HXA, SXA, K1HXA and K1SXA. Conduit 54" Inner Wire 65" Wire Travel 9"

Replaces Honda 54530-VEO-003. Fits models HRB215XA, HRB215K15XR and HRB215K2HXA. Conduit 45" Inner Wire 54-3/4". Wire Travel 9-1/4"

Replaces Honda 54530-VB3-802. Fits models HR214SXA and HRA214SXA. Conduit 53" Inner Wire 65-1/2" Wire Travel 10"

Replaces Honda 17910-VA4-800, Code 1663483. Conduit 36-1/2", Inner wire 41-1/4", Wire travel 1-3/4".

Replaces Honda 96150-60020-10, code 0876904. Fits 21" commercial mowers. Sealed two sides. (37/64"ID, 1-1/4"OD, 23/64" height).

Replaces Honda 91055-VA4-K10. Fits 21" walkbehind & self-propelled mowers. (1/2"ID, 1-1/8"OD, 13/32" height).**Limited supply-discontinued item**

Sporty, dynamic styling brings this ultra-light protective spectacle into the realm of true wearing enjoyment. Innovative, six-base lens provides a more contoured fit and panoramic viewing area. Resilient nylon frame is gloss black. Abrasion resistance and ultraviolet protection are integrate elements in the hard coated polycarbonate lenses which block in excess of 99.9% of harmful UV light. Meets ANSI Z87.1 and CSA Z94.3 standards. Gold Mirrored Lens. **LIMITED SUPPLY--discontinued item**

Sporty, dynamic styling brings this ultra-light protective spectacle into the realm of true wearing enjoyment. Innovative, six-base lens provides a more contoured fit and panoramic viewing area. Resilient nylon frame is bright red-(limited supply). Abrasion resistance and ultraviolet protection are integrate elements in the hard coated polycarbonate lenses which block in excess of 99.9% of harmful UV light. Meets ANSI Z87.1 and CSA Z94.3 standards. Gold Mirrored Lens. **LIMITED SUPPLY--discontinued item**

Sporty, dynamic styling brings this ultra-light protective spectacle into the realm of true wearing enjoyment. Innovative, six-base lens provides a more contoured fit and panoramic viewing area. Resilient nylon frame is gloss black.  Abrasion resistance and ultraviolet protection are integrate elements in the hard coated polycarbonate lenses which block in excess of 99.9% of harmful UV light. Meets ANSI Z87.1 and CSA Z94.3 standards. Gray Lens. **LIMITED SUPPLY--discontinued item**

Sporty, dynamic styling brings this ultra-light protective spectacle into the realm of true wearing enjoyment. Innovative, six-base lens provides a more contoured fit and panoramic viewing area. Resilient nylon frame is royal blue.  Abrasion resistance and ultraviolet protection are integrate elements in the hard coated polycarbonate lenses which block in excess of 99.9% of harmful UV light. Meets ANSI Z87.1 and CSA Z94.3 standards. Gray Lens. **LIMITED SUPPLY--discontinued item**

120 piece assortment contains 6 of the most popular size hose clamps.

Replaces Husqvarna O.E.M. #539-101-733.  Length 21", Center Hole 5/8", Width 2-1/2", Thickness .204 (3)blades for 61" cut.

Replaces O.E.M. #539-107709. 48" Deck Belt-model CZ4817 - OEM spec belt.

Replaces O.E.M. #539-107710. 48" Deck Belt-model CZ4817 - OEM.

Replaces Husqvarna OEM # 539-103241. 48" Zero Turn Pump Belt - OEM

Replaces Husqvarna OEM # 539-103687. Deck Belt - OEM

Replaces O.E.M. #539-100-340, Length 16-1/4", Center Hole 5/8", Width 2-1/2", Thickness .204 (3)blades for 48" cut, Fits Husqvarna, Yazoo, Kees Commercial Mowers.

Replaces O.E.M. #539-1032-74. Length 14-7/8", Center Hole 5/8", Width 2-1/2", Thickness .204. (3) blades for 42" cut Commercial Mowers.

Replaces OEM#503135001. Fits model 394.

Replaces Husqvarna #539102652. Fits mid mount ZTR commercial riders. Also replaces Yazoo/Kees #102652. ID-5/8" OD-5" Height-1-1/4"

Replaces Husqvarna O.E.M. #539-104336 & Yazoo # 104336 . Deck Belt-large frame mowers - OEM spec belt.

Replaces Husqvarna O.E.M. #539-105477 & Yazoo 105477. Deck Belt-large frame mowers - OEM.

Replaces O.E.M. #716886. Length 6-7/16", Center Hole 29/64", Width 1-1/4", Thickness .095. Takes 8 blades per unit. Shredder blade. Used on 260K

Replaces O.E.M. #712224. Length 4-11/16", Center Hole 29/64", Width 1-1/4", Thickness .095. Takes 8 blades per unit. Shredder blade. Used on 251K

Replaces O.E.M. #054627. Length 23-7/8", Center Hole 1/2", Width 2-3/4", Thickness .187. (3) blades for 72" cut. 72" 3-way deck. Model 922831.

Replaces O.E.M. #015651. Length 24", Center Hole 3/8", Width 2-3/4", Thickness .187. (3) blades for 72" cut.

Flat Idler Pulley replaces Hustler #781385. Fits 52", 60" & 72" Super Z deck assembly. ID-11/16" OD-6-3/4" Height-1-1/2"

Flat Idler Pulley replaces Hustler #781856. Fits 52", 60" & 72" Super Z drive units. ID-11/16" OD-5-1/2" Height-1-5/16"

Replaces Hustler/Excel OEM #781443. Hydro Pump Belt - Fits Z & Super Z - OEM spec belt.

Replaces Hustler/Excel OEM # 781310. 60" Deck Belt. Z & Super Z - OEM spec belt.

Replaces Hustler/Excel OEM #784207. 72" Deck Belt - Z & Super Z - OEM.

Replaces Hustler/Excel OEM #782292. 52" Deck Belt - Z & Super Z - OEM.

Replaces Hustler/Excel OEM # 786533. 52" Hydro Pump Belt- Mini Z & Super Z - OEM spec belt.

Replaces Hustler/Excel OEM #786483. 52" Deck Belt - Z & Super Z - OEM.

Replaces Hustler/Excel OEM #786491. 44" & 48" Deck Belt - Mini Z & Super Z - OEM.

Replaces Hustler/Excel OEM 784231. Hydro Pump - Fast Track - OEM.

Replaces Hustler/Excel OEM #784249. 52" Deck Belt - Fast Track - OEM.

Replaces Hustler/Excel OEM #784322. 44" Deck Belt - Fast Track - OEM.

Oil filter replaces Hydro Gear HG52114.  Fits transmission model ZT2800.  Also replaces Scag HG52114, fits Freedom Z, Exmark 109-3321, Hustler 768341 & 600976.

Hydro Pump replaces: Hydro Gear #BDP-10L-117P, Bunton # PL6007, Encore #453087, Exmark #613042, 1-613042 and 1-321008 for Turf Tracer Hydro Models, Gravely #051146, 05330, 08867351, 08867300, 09279900 fits Pro 300 Models, Kees #101111, Snapper #2-7127, Scag #48551 fits SWZ #BDP10L-504, BDP-10L-117, Walkbehinds, STT61 Hydrostatic STC/SMTZ/SCR. 1000 PSI continuous operating pressure. Confirm O.E.M.# prior to ordering. 25% restocking fee on all returned Hydro Pumps.

Replaces Exmark #1-603841, 603841,and 103-2766, Hydro Gear #BDP-10L-121P. Fits Lazer Models Hydro Gear. Confirm O.E.M.# prior to ordering. 25% restocking fee on all returned Hydro Pumps.

Replaces Bunton PLO786 and Replaces John Deere PT8761 and AM106564. "V" belt Idler. ID- 3/8", OD- 4", Height- 1".

Ignition switch replaces John Deere AM122881. Snap in mounted, 3 position switch. Uses our MP-9667 key.

Replaces Toro # 40-5940 & #29-5560 models 5200 and 5620 snowblowers. Fits 32", 36", 37", 44" and 52" mid-size commercial mowers with pull start. Includes mounting hardware.

Replaces AYP #158913, Exmark #543070, Hustler 045898 and Noma #305720. Fits Exmark Laser ZTR models and John Deere STX 38446 models

Replaces John Deere #AM38227. For John Deere front mount mowers. Fits series 300 and some 200's. (Magneto)

Multi-application ignition switch fits Scag 48609, Exmark 403121, Ferris 1521842, Gr.Dane D18090, LawnBoy 700171 & 740015, Snapper 17817, Murray 56419, Ariens 02456500 & 52406900, & CubCadet 725-3232. Also fits single stage Simplicity & Snapper snowthrowers. Also fits AYP, General Power, Grasshopper, Homelite, Noma, Troy Bilt. Includes key, lock-washer nut & cover. 2 terminals/2 positions.

Multi-application ignition switch replaces AYP 144921, 163088, Murray 327355, Simplicity 1718306 & 1713845. Thread mounted. Uses our MP-9668 nut & our MP-9667 key.

The tester checks the integrity of the electrical ignition and magneto/coil ignition systems of lawnmowers, boat motors, motorcycles and automobiles. The tester checks both current and voltage and will indicate fouled electrodes, E-Z view LED and neon lamps for easy accurate reading, pocket size, high impact ABDS plastic casing.

5/16" Press - Inside Diameter - 1/2", Outside Diameter - 1-3/8".

5/16" Press - Inside Diameter - 3/4", Outside Diameter - 1-3/8".

5/16" Press - Inside Diameter - 3/8", Outside Diameter - 1-3/8".

5/16" Press - Inside Diameter - 5/8", Outside Diameter - 1-3/8".

5/16" Press - Inside Diameter - 7/16", Outside Diameter - 1-3/8".

**limited supply--discontinued item**                  
                                 

5/16" Press - Inside Diameter - 9/16", Outside Diameter - 1-3/8".

**limited supply--discontinued item**                  
                                 

Heavy duty fuel filter with universal duel hose barbs that fit 1/4" & 5/16" ID fuel line.  80 Micron rating.  MADE IN THE USA.  Features a high impact polymer-copolymer blend that will stand up to all standard and bio-based fuels including E85. 

3-1/2" long

058" throttle wire, 100' rolls. Used with our conduit #TC247.

072" Hvy. Duty clutch cable, 100' rolls. Used with our conduit #TC248.

Replaces O.E.M. #551761. Walkbehinds - Variable Speed, 36" Main Belt.

Comes with grease fitting and safety sleeve. Replaces Bobcat 38204,Encore 363353, Exmark 324157 & 323275, Gravely 049013, 08870100, Scag 46513 and 48226, Toro 514260. For 36", 48", 52", and 61" walkbehind mowers.

Replaces Bobcat #38456 and #38018N and Snapper/Kees 57582/77285. ID- 5/8", OD- 3-1/2", Height- 1-5/16", Keyway- 3/16".

Replaces O.E.M. #500904, 330721. Length 14-7/8", Center Hole 7/16", Outside Hole 1/2", Width 2", Thickness .150. (3) blades for 42" cut.

Replaces O.E.M. #500905, 330720. Length 17-1/4", Center Hole 7/16", Outside Hole 1/2", Width 2", Thickness .150. (3) blades for 50" cut.

Replaces O.E.M. #182185. Walkbehinds (5 Speed), Wheel Drive Belt - Double V Belt - OEM.

Replaces O.E.M. #336486.  72" - Secondary Belt.

Replaces O.E.M. #331807.  21" Commercial Deck - MTR/Jackshaft.

Replaces O.E.M. #331808.  Jackshaft/Reducer belt

Replaces O.E.M. #551763. Walkbehinds - Variable Speed, Transmission Belt.

Replaces O.E.M. #557162. Wheel Drive Belt- double V Belt-OEM

Replaces O.E.M. #551778. Walkbehinds - Variable Speed, 48" Main Belt.

Replaces O.E.M. #336481 - Traction Belt. *This item is not in our current catalog*

Replaces O.E.M. #336485. 72" - Primary Belt.

Replaces O.E.M. #390514. Length 20-3/4", Center Hole 7/16", Outside Hole 13/32", Width 2-1/2", Thickness .240. (3) blades for 60" cut. Commercial Turfcat.

Replaces O.E.M. #390515. Length 25", Center Hole 7/16", Outside Hole 13/32", Width 2-1/2", Thickness .240. (3) blades for 72" cut. Commercial Turfcat.

Replaces O.E.M. #552284, Wheel size 410/350-4, Caster wheel on 48" commercial walkbehind mowers / 410/350-4, 2-ply stud mounted 3-piece wheel with 3/4"open cage roller bearing and zerk fitting, painted white. **Discontinued Item--Limited supply**

Replaces O.E.M. #M115496. Length- 18-5/8", Center Hole- 13/16", Width- 2-1/2", Thickness- .204. Commercial Mulcher Blade. (3) blades for 54" cut.

Replaces John Deere #M84691. Also fits Cub Cadet # 938-3056 and AYP #137644/184291. 2-9/16" shoulder length and 13/16" thread length.

Replaces John Deere O.E.M. #AM34770 and AM39687. Also fits Onan #122-0469. Thread size 3/4"-16, OD 3", HT. 4-13/16", Micron 28.

Replaces OEM #AM101589. Wheel size 11/400-5, polyurethane smooth tire on 1-piece yellow wheel with 3/4" ball bearing. Flat Free Tire.

Replaces OEM #AM115510. Wheel size 9x350-4, 4-ply polyurethane smooth tire on 1-piece yellow wheel with 3/4" open cage roller bearing. Flat Free Tire.

Replaces John Deere #AM107344, Bobcat #48587, Briggs & Stratton #397975/493988/493988S, Encore #363257, MTD 751-3111/951-3111, Murray 23711/92317, Simplicity 1678045/1714020, Snapper 1-2515/1-9378. Also fits Ariens, Troy Bilt, Toro, Gilson and other brands. For new style tanks. 2-1/8" dia. Vented with shutoff. Made by an OEM supplier.

Replaces John Deere belt OEM# M118685 for 54" deck on Lawn & Garden Tractors.

Deck belt replaces John Deere OEM# TCU13195. Fits John Deere 737 and 757, serial numbers 03000 and lower.  OEM spec. belt. Covered belt.

Replaces John Deere belt OEM# M143019 for Lawn & Garden Tractors.  Also fits M118684.

Replaces John Deere belt # GX20006 drive belt for Lawn & Garden Tractor.

Replaces John Deere belt OEM# GY20570 & GX20072 for 42" deck on Lawn & Garden Tractor.

Replaces John Deere OEM# M131958. 3 blades used for 60" cut. 21" length, 2-1/2" width, 29/32" center hole, .250 thick. Fits Z-Trak models M655, M653, F680 and 4000 series.

Walkbehind - see Bunton blades - order BU16 blades - for older Walkbehinds.

Walkbehind - see Bunton blades - order BU18 - for older Walkbehinds.

John Deere GS/36" Heavy duty military spec. latch, Curved front directs grass to back of catcher for high density packing, Non vented front construction of catcher keeps grass from clogging mower outlet. Jumbo weighs 23# and holds 4.3 cubic feet. Tubular steel frame continuous weld superior to spot-weld catchers, 22 gauge solid and perforated sheet steel.

Hi-Lift blade replaces John Deere OEM# TCU15881.   Length- 21", Width- 3", Centerhole- 29/32", thickness- .250.   Fits John Deere models 737, 757, 777, 797 & 997 with 60" cut decks.   3 blades used for 60" deck.  

Replaces O.E.M. #M80783, AM38314, AM102402, M141786, Length 24-15/16", Center Hole 29/32", Width 2-1/2", Thickness .313. (3) blades for 72" cut, 1" lift.

Replaces O.E.M. #M136194. Also can be used to replace # M136185. Length 17", Center Hole .904", Width 2-1/2", Thickness .240 (3)blades for 48" cut, Fits 7-Iron Decks.

Replaces O.E.M. #M145476, and M127500. Length 17", Center Hole .800", Width 2-1/2", Thickness .204 (3)blades for 48" cut, Fits 48C Decks, Since 1999.

Replaces O.E.M. #M143520 & M145516. Length 19", Center Hole .800", Width 2-3/4", Thickness .204. (3)blades for 54" cut. Fits 54C Decks.

Replaces O.E.M. #M139976, Length 21-3/8", Center Hole 13/16", Width 2-1/2", Thickness .203. (3) blades for 60" cut. Fits new style decks from 1999.

Replaces O.E.M. #GC00344, Length 21", Center Hole .3/8", Width 2-3/4", Thickness .125. Mulching blade. Fits 21" steel decks. Walkbehind mowers.

Replaces O.E.M. #GX20250, Length 17", Center Hole .675", Width 2-1/2", Thickness .150. Fits L120 & L130 series riders. (3) blades for 48" cut.

Replaces O.E.M. #GX20249, Length 21", Center Hole .675", Width 2-1/2", Thickness .150. Fits L100 & L110 series riders. (2) blades for 42" cut. Also fits Sabre and Scott mowers.

Idler Pulley replaces John Deere #GX20287. Fits L120 Series 20 HP - 48" deck and L130 Series 23 HP - 48" deck ID-11/16" OD-3-11/32" Height-1"

** LIMITED SUPPLY, DISCONTINUED ITEM **

Deck belt replaces John Deere OEM# M110313.  Fits 48" deck, LX & GT series.  OEM spec belt

Replaces John Deere GY20629. Fits L120, L130 lawn tractors. Fits G110 Garden Tractor. ID 43/64", OD 5-7/32", Height 1-23/32".

Replaces John Deere OEM# M154061 and AM137327.  Heavy duty blade.  Fits 42" riders Models 102, 115, 125 & 135.  2 blades used for 42" cut.

Length- 21", Centerhole- 7 point star, Width- 2-3/4", Thickness- .204

 

Replaces John Deere OEM# TCU15882.  Hi-lift blade.  3 used for 72" cut on 777, 797, 997, 1400 & 1500 series front mowers. 

Length- 25", Centerhole- .900, Width- 3", Thickness- .250"

 

John Deere deck belt replaces OEM# TCU13196 used on 737 & 757 54" deck.  OEM spec. belt

Replaces O.E.M. #M115759. Length 14-1/16", Center Hole 11/16", Width 2-1/2", Thickness .204. (3) blades for 38" cut. Shallow deck.

Replaces O.E.M. #AM104489. Length 16-1/2", Center Hole 5/8", Width 2-1/2", Thickness .204. (3) blades for 48" cut.

Replaces O.E.M. #M113517. Length 16-5/8", Center Hole 13/16", Width 2-1/2", Thickness .204. (3) blades for 48" cut. Fits model F710. Mulching blade

Replaces O.E.M. #M115495. Length 16-5/8", Center Hole 13/16", Width 2-1/2", Thickness .204. (3) blades for 48" cut.

Replaces O.E.M. #M112991. Length 19-1/2", Center Hole 11/16", Width 2-1/2", Thickness .204. (2) blades for 38" cut. Mulching blade

John Deere deck belt replaces OEM# TCU18602 on Zero Turn mower.  OEM spec. belt

Replaces O.E.M. #M113518. Length 18-5/8", Center Hole 13/16", Width 2-1/2", Thickness .204. (3) blades for 54" cut. Fits models F-725. Mulching blade.

Replaces O.E.M. #M115496. Length 18-5/8", Center Hole 13/16", Width 2-1/2", Thickness .204. (3) blades for 54" cut.

Replaces O.E.M. #M87622, AM100538, M141785, Length 20-1/2", Center Hole 29/32", Width 2-1/2", Thickness .313. (3) blades for 60" cut.

Replaces O.E.M. #PT6921. Length 20-3/4", Center Hole 3/8", Width 2-1/4", Thickness .150. For Walkbehind.  **Limited Supply**

Replaces O.E.M. #M112972, M112738, M125413. Length 21", Center Hole .908, Outside Hole .411, Width 2-3/4", Thickness .134. 21" mulching blade for models GX14SB & GX14SBE.